Husqvarna
Yth2454 mower belt keeps coming off. bearings and pullys are good. could it be the electric clutch?
Experienced gardeners share their insights in answering this question :
Simply.no
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Your riding mower belt keeps coming off because of several possible causes such as a damaged, dirty, or incorrectly installed belt. This problem can also be due to an oil leak, damaged mower pulleys, damaged bearings, or a misaligned or stretched out belt.
Belt slipping off tensioner pulley is a common issue that can occur with any type of belt-driven system. The most likely cause is that the tensioner pulley itself is worn out or damaged. In some cases, the problem may also be caused by a misaligned pulley or by a loose belt.
A common cause of belt breakage is excessive grass clippings on the deck. Grass clippings can work their way under pulleys and deck covers, causing series problems. Make sure to clean off your deck after every mower use and follow manufacturer recommendations.
Husqvarna Riding Mower Belt Keeps Coming Off
The belt may come off due to an improperly tensioned belt, an over-tightened belt, or a broken belt. It is important to properly tension the belt and ensure it is not too tight in order to prevent it from coming off.
Check on how the belt gives way to your pressure; it should not be loose enough to give way more than a few inches. For mower belts that give way more than two inches, you need to tighten them according to the model`s manual.
There is no specific time length that mower belts need to be replaced. Some belts may last longer than others due to different operating conditions. One thing is for certain though, the more the mower is used, the sooner you will need to consider replacing the mower belt.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Belt for self popelled mower keeps breaking? Cannot keep a new belt on pulley
ANSWER : Check that the pulley isn’t seizing up and causing the belt to snap, also be sure you loosen up the self propelled mechanismn by spraying down with WD 40, too much belt tension can cause this, but it rather seems like the belt pulley seizes and the engines drive pulley keeps turning causing the belt to overheat and break or stretch and come flying off.
Read Full Q/A … : Husqvarna
ROUTING OF BELT – Mtd Drive Belt 42"
ANSWER : Diagram is on the mowing deckBest regardsCk
Read Full Q/A … : Husqvarna
Why the engagement belt keeps falling off – Ariens 42" 19HP Lawn Tractor
ANSWER : Your idler pulley spring broke or come unhook.
Read Full Q/A … : Husqvarna
Replaceing mower deck belt on 20 hp 42 mower model no 917275660. Got the belt on. How do I get the cluch spring back on.
ANSWER : Are you refering to the spring attached to the end of the cable that runs up to the lever on the dash to engage the blades? All you needed to disconnect was that cable on top of the idler arm that’s held in place by a ‘hairpin’ and the left pulley cover to put the belt on.
Read Full Q/A … : Husqvarna
LT1045 keeps breaking NEW belts after just a short period of mowing.
ANSWER : Have you checked the bearings?
Read Full Q/A … : Husqvarna
What size for a 611 deutz allis 42 in deck – Mtd Drive Belt 42"
ANSWER : Go to simpletractors.com they may have the answer for you !
Read Full Q/A … : Husqvarna
Why does my mower deck belt on john deere 316 keeps breaking
ANSWER : There are a few causes for this and its not just this brand or model. First check that belt is installed correctly, check the part that keeps the belt on the belt rollers the belt should be between the garde and belt wheel, check for shine spots where belt is rubbing, Some times the mower deck is not set even or too low it can put the belt at too much of an angel causing the top of roller to cut it. So check the deck level there are adjustment devices on the mower to adjust, check for shine spots and for correct belt installment, and check roller wheel top for cuts or sharp spots, and check belt tension to see if it is to tight or too lose, also check that rollers spin free and there is not one stuck that could be heating the belt up too much, And last but not least make sure you are using the proper belt that is made for a mower fan belts don’t last very long on a mower.
Read Full Q/A … : Husqvarna
Need the mower deck belt size for a allis chalmers t-811 lawn mower
ANSWER : 42″ deck 1/2 x 120 P/N 1668066SM
48″ deck 1/2 x 126 P/N 1703466SM
48″ deck 1/2 x 126 P/N 1703466SM
Read Full Q/A … : Husqvarna
