Garden

Experienced gardeners share their insights in answering this question :
Drive belt maybe slipping

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Always check before substantially raising the level of your garden. In general, increasing the ground level may require planning permission. If you`re levelling out a sloping garden, you may not need permission, but it depends on whether you affect your neighbours` view.
Concrete blocks are very suitable for slopes as they can be built as sturdy, retaining, edges and features. ‚ÄčThis helps to stabilise the ground, create flat terraces and form structure within a garden design. Smaller concrete blocks such as block paving can also make effective mow strips on slopes.
Spread the soil until it`s roughly even with your level-grade line. Use a shovel, landscaping rake, or flat spade to gradually redistribute the soil from higher areas to lower areas until your entire site has a uniform appearance. As you work, keep an eye on your string lines for reference.
Once you`ve mowed the lawn, mix together some fine sand with some compost from your yard (at a ratio of 40% sand, 60% soil) and apply it to the low areas evenly. Rake even if you have one and run a household broom over it to work it into the grass, water and monitor progress. Repeat if needed.
Having level beds ensures the even distribution of fertilizers and other amendments you add to your soil. As rain hits a non-level raised bed, another thing can be unevenly distributed: your growing medium itself. You can end up with some rather severe erosion issues if you don`t level off your beds.
Topdressing involves spreading a leveling mix of topsoil, compost, and fine sand. The soil should not contain mulch or plant debris, which can smother the grass. The best sand to use is play sand, which you can buy at any home center. A typical mixture is 40 percent sand, 40 percent topsoil, and 20 percent compost.
Slope of the land is essentially the gradient or incline of the land. A steep slope refers to a sharp incline; a gentle slope refers to a slight incline.
Use a Concrete Leveling Compound

This can be done in a few different ways, including using a pressure washer or a commercial acid-based concrete cleaner. This is followed by grinding away the top layer of concrete to create a rough surface for the bonding agent to adhere to.

Grass and shrubs are very effective at stopping soil erosion. This is primarily because plant roots tend to hold soil together, making it harder to erode. The leaves of the plants also help to reduce the velocity of raindrops falling on the ground, making it harder for them to dislodge the soil and erode it.
Granite paving is one of the best materials for a sloping path. Granite is naturally slip-resistant, which makes it one of the safer materials for a patio or path, particularly a sloping one. Granite is very durable and resilient, meaning it is well suited to the rigours of being used regularly as a walkway.
The most tried-and-true way to landscape a slope is to add some form of a retaining wall. And there`s a range of ways to riff on traditional retaining structures. Consider affordable woods steps or, for a more expensive option with an artsy twist, even an arch wall.
In order to raise your gardens level most of the time you will need to install retaining features. These usually take the form of retaining walls or garden edgings with retaining foundations. These will be especially needed if you need to raise the soil level by more than a few inches.
How steep is too steep? A slope ratio of 2:1 drops one foot in every two horizontal feet. This is considered the most extreme that will support plants, and even then they often fail because water runs off before it can saturate the root zone.
Spread the soil until it`s roughly even with your level-grade line. Use a shovel, landscaping rake, or flat spade to gradually redistribute the soil from higher areas to lower areas until your entire site has a uniform appearance. As you work, keep an eye on your string lines for reference.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.

Read Full Q/A … : Garden

Chain saw won’t start – pull starter pulley hard to pull?
ANSWER : If it worked fine the last time you used it, then pull the spark plug and try pulling the rope. See if it’s easier or if gas shoots out of the plug hole. I’ve seen this happen when the diaphram in the carb goes bad from sitting over winter. It loads up the cylider with fuel and makes it very difficult to pull the rope. If there is no fuel in the cyliner and it’s still hard to pull, make sure there is nothing binding the clutch/sprocket. I’ve had chucks of wook lodged in there that caused it to bind the crank output, which resulted in a hard pull on the rope as well.

Read Full Q/A … : Garden

Hard to pull starter rope. It doesn’t pull smoothly. hard to pull.
ANSWER : Take the spark plug out–does it pull smoothly now? If not, the pull cord may be the wrong size or it is damaged and/or doesn’t rewind correctly. Does the machine have a compression release? If so, it may be plugged with carbon. With the spark plug out, pull the engine through several times briskly with the throttle open and the choke off to expel any excess fuel from the crankcase. Hope some of this helps!

Read Full Q/A … : Garden

When I pull the cord, the string is hard to pull and recoils out of your hand about half way through the pull
ANSWER : Sounds like you have two problems. One the flywheel brake is not being released completely and second the flywheel key has been sheared. It is why the rope is being jerked out of your hand. The mower is out of timing and when the spark plug fires before it is suppose to, it jerks the rope out of your hand.

Read Full Q/A … : Garden

Troy Bilt Lawn Mower pull Cord broken
ANSWER : There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on

Read Full Q/A … : Garden

My chainsaw starts when there is no bar and chain on it but when I put the bar chain and side casing back on tighten the chain and pull the starter cord it is hard to pull and then the chain goes loose again
ANSWER : Have you just replaced the chain?If so there is a possibility the chain and drive sprocket don’t match causing the engaging spurs to ride on the sprocket teeth

Read Full Q/A … : Garden

How do you attached the engine pull cord? – Poulan 18" Wild Thing Chainsaw
ANSWER : Thread the cord through the starter pulley, wrap the end of the cord once around the pulley pinion and into the small cut a way in the drum, there should then be a small self tapping screw which screws down to secure the end of the rope, if you can tie a small enough knot this will also do to stop the rope coming out of the pulley.

Read Full Q/A … : Garden

When i pull the rope it backlashes half way through the pull
ANSWER : Hi, You have most likely sheared the flywheel key which puts the timing out. Remove the flywheel and replace the key. Regards Phil.

Read Full Q/A … : Garden