Garden

10 hrs of use after drive belt change. goes fine in forward
Experienced gardeners share their insights in answering this question :
Something in the trans or your drive line is loose or broken.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Riding mower not going forward or reverse could be caused by a number of issues. The most common cause is a stuck or broken clutch, which prevents the mower from moving. Other causes could include a broken or disconnected drive belt, damaged transmission, or a problem with the mower`s starter or ignition system.
The reasons why mower is not moving forward or reverse is that the battery is dead, or due to clogged fuel line. Additionally, malfunctioning transmission, or a broken drive belt, also a faulty spark plug, even when friction wheel isn`t in contact with the friction plate, or damaged Tires.
If the blades are engaged and you shift to reverse the mower is designed to either shut off the blades or the engine. Some units have ROS, this is an additional position on the key switch that can be activated if the operator feels the need to mow in reverse.
Yes you can. Although mowing in reverse is not recommended, there may be certain situations where operators feel they need to mow in reverse.
Can you pull a self-propelled lawn mower backwards? Yes, you won`t cause any damage to the mower by pulling it backwards.
Your Mower Won`t Start:

Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.

If there is interference with the brake/clutch pedal, your gear shifter may not come out of the neutral position. Inspect the linkage between the clutch/brake assembly and wheels, as well. Any damage or obstructions should be repaired immediately since this also causes a safety issue.
The only thing when pulling it backwards, is that you need to make sure you move it forward a couple of inches after releasing the self propel lever, so it doesn`t lock up.
Turning a lawn mower upside down is generally not advised. This is because the fuel and oil systems may be affected by the change in orientation, and this can lead to damage or malfunction. Additionally, the spark plug can be damaged by being in contact with the ground, and the blades may become blocked by debris.
Most lawn mower blades rotate in a clockwise direction (counter-clockwise when viewed from below), and as such have the cutting edge on the right side. If you are unsure of how your mower rotates, check the position of the discharge chute; if it is on the right side angled back, the blade turns clockwise.
Sharpening or replacing the mower blades is also the answer if grass tips look ragged or tattered instead of cleanly cut. Blade vibration also causes an uneven cut. To eliminate vibration, replace unbalanced blades and worn mandrels. Replace a worn blade belt because a worn belt won`t spin the blades correctly.
Change the mowing pattern each time you mow. Grass develops a grain based on your cutting direction, tending to lean towards the direction you mow. Alternating your mowing pattern causes upright growth and prevents ruts from growing in the lawn.
In this case, the vertical component of the applied force acts in the direction of the weight of the mower. This the effective weight of the mower. Since the effective weight of the lawn mower is lesser in the first case, pulling the lawn mower is easier than pushing it.
The most common cause of a mower that runs for thirty minutes and then dies is a faulty armature. A faulty gas cap is the second most likely cause.
A dirty carburetor is one of the most common causes for a lawn mower not being able to start after sitting unused for months or years at a time.
Varying the pattern in which you mow will help to allow the blades to grow straighter and healthier. Grass blades tend to grow in the direction in which they are mowed. Alternating the pattern allows the blades to return to a more upright position.
Your Mower Won`t Start:

Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.

Check the drive belt that is located just above the mower deck. Follow the belt as it wraps around the deck and to pulleys under the engine and the rear tires. Make sure the belt is secured to the pulleys, because if it is not, then the belt (and thus the mower) will not move. If the belt looks broken, replace it.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Mower won’t start
ANSWER : This may sound stupid but don’t mean it to…
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.

Hope it helps.

Anthony

Read Full Q/A … : Garden

Toro 149cc Lawn Mower Won't Start – Toro Lawn Mower With Toro Power Tools
ANSWER : Bad carburetor your old fuel jammed up the jet so it won’t get fuel and if it does it will start and shut off So replace the carb or try to clean the jet and run non oxy fuel only

Read Full Q/A … : Garden

My toro 6.5 hp push mower (2010), has no fire to the plug. I have not abused it. i have a small yard and it just gets normal use. Now it won’t fire. I first changed the fuel and cleaned the carb thinking it was that crappy ethanol again. but i grounded out the spark plug and cranked it…no spark. I think it has to do with the lever you pull back to start it . they have some stupid complicated safety contraption that rides along the fly wheel when you pull back on the handle for starting and shutting off the engine. …it looks worn out already…like a mini brake pad. any ideas?…do i really have to replace this garbage every year or am i on the wrong path here?
ANSWER : Unhook your wire from the coil that goes to shut off mechanism, and see if you have spark then. the wire may be grounded out, or your coil might have took a ****

Read Full Q/A … : Garden

I have had a poulan pro 550 series push mower for almost 1 year at the end of the season last year the mower would start briefly and then stop. i have cleaned out the air filter and that did not help.the mower started, i made one revolution around the yard 3/4th of the way the mower quit. I then primed the mower it started then quit and now it will not start at all. Does anyone have any suggestions of what to do. Thanks
ANSWER : There is a little spring that works the carburetor arm. If that popped off then the mower will not run.

Read Full Q/A … : Garden

My mower will start but won't stay running – Toro LX466 22HP Lawn Tractor 13RT61RH244
ANSWER : I am going to respond 2 times to this post. The first reply will be generic things to check.
First off check the oil level and make sure it is serviced to full.
If your having a lack of fuel (runing lean) you will need to check fuel flow at the carb fuel mainfold. It should fill a spray paint can lid in less than 10 seconds but teting flow rated of the main fuel line. If you have poor flow here… you need to check the fuel filter and the fuel tank outlet port for obstructions.

Good Fuel flow still shutting off…. remove the carb float bow and clean the debris from the bow’ and the treaded area where the fuel solenoid mounts Additionally you will have to again remove the main fuel line and spray carb cleaner in the float needle area to flush out any debris through the fuel hose connection.

For the second response I need to know which engine is installed on your mower by MODEL number if you can locate it. (there are 3 engines) At least try to find the engine model number. If you can not locate it Brand and HP of the engine (I assume 22 hp) Thanks for choosing FixYa,
Kelly

Read Full Q/A … : Garden

Lawn mower cranck but wont start…
ANSWER : Since you already checked for spark and air I would drain all the fuel out of it and check that fuel for water. Over time some lawn mowers end up with contaminated fuel. You can see the water sitting on the bottom of the fuel if you let it stand for a bit in a small plastic bowl.

Be sure to empty and dry out you fuel can as well. Especially if the mower stopped running right after a refuel. Which is a good sign your gas can is contaminated too.

Read Full Q/A … : Garden

B&S Quantum Power 4hp won’t start with fresh plug,
ANSWER : Did it run before you changed the plug?Gap is correct, flywheel shear pin may be bad, Water in the Gas?

Read Full Q/A … : Garden

I have a Poulan push mower that after mowing in a ditch started making a loud noise and running rough. It almost sounded as if metal was hitting metal. The mower was vibrating more than normal. I checked under the mower and nothing is hitting. After a few times of stopping the mower engine because it sound as if it is going to die down the mower will not start now. The shaft does not appear bent and the blade appears ok. The mower has oil, a good spark plug and a clean air filter. It was running fine until that moment. I did not see anything that I hit but it is possible I hit something in the ditch like a pine cone or branch. What could the problem be and how would I go about fixing it?
ANSWER : If you are sure the oil level is correct then it sounds like it’s about to die, unfortunately. A pine cone shouldn’t cause any damage, but a large branch may do so. Was it smoking before you shut it down? The vibration could be caused from a bent blade. It could also be caused from a part breaking in the motor. I wish I could have given you better news!

Good Luck,

Jim

Read Full Q/A … : Garden