Garden
why gt 2554 pto belt keeps breaking
Experienced gardeners share their insights in answering this question :
Bad spindles in deck get the deck up get pair of glove jerk the hell everyvery one those blades replace spindles that move around
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If a belt is not tensioned properly, it will ride too loose or too tight on the pulley. A belt that`s too loose on a pulley will cause slippage, which leads to heat build up from friction. This heat will damage your rubber belts and cause the belts to crack and break.
Bad Bearings in the Pulleys or Spindle Housings
Bad bearings in the pulleys or spindle housings could also be a reason why your Cub Cadet deck belt keeps coming off. First, examine your mower`s pulleys and ensure they are parallel to the deck and level. If they are not, the belt could come off the pulley.
The PTO (or power take-off) belt is part of a pulley system that operates the blades on your riding lawn mower. It runs off the electric clutch system in your engine.
Things You`ll Need
Your Cub Cadet LT1045 comes with two belts that, over time, will need to be replaced as their rubber ages.
If a belt is too tight in a system, it can add stress to your bearings. The added stress to bearings can result into over amperage of your motor and potential motor failure.
Improper belt tension is the most common and obvious cause of slip, which generates unwanted heat. The friction that occurs when a V-belt slips in a pulley causes belt sidewalls to become glazed, and decreases gripping ability.
There is no specific time length that mower belts need to be replaced. Some belts may last longer than others due to different operating conditions. One thing is for certain though, the more the mower is used, the sooner you will need to consider replacing the mower belt.
Home and Garden Geek adds that you should be able to loop one or two fingers over the same belt when the tractor is off and the belt is “engaged” and pull it gently away from the pullies. This translates to one or two pounds of force. If you need more than two fingers, your deck belt may be too tight.
Cub Cadet Built In America Since 1961
Cub Cadet`s innovative products are designed and engineered in Valley City, Ohio — the headquarters of its global operation. Hundreds of local employees in the United States ensure that every detail is just right.
Cub Cadet 3-in-1 Front Wheel Drive Lawn Mower with 160 cc Honda Engine – 21-in.
Improper drive maintenance is the biggest source of belt drive problems. Angular misalignment (Fig.
They`re usually good for 10 years or 150,000 miles. Even so, don`t neglect your car belt maintenance. It`s still a good idea to have a mechanic check the belt from time to time. Usually they`ll do this as a courtesy if you`re in for an oil change or other servicing.
The general rule is if there are three or more cracks within a three-inch section of the belt, then your belt needs replacing.
Belts, pulleys and tensioners should be inspected on a regular basis, with each oil change performed on the vehicle. Some of the symptoms to look and listen for are: Belt Cracking – 3 or more cracks in a 3” section means it is time to replace it.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
LT1045 keeps breaking NEW belts after just a short period of mowing.
ANSWER : Have you checked the bearings?
Read Full Q/A … : Garden
Belt for self popelled mower keeps breaking? Cannot keep a new belt on pulley
ANSWER : Check that the pulley isn’t seizing up and causing the belt to snap, also be sure you loosen up the self propelled mechanismn by spraying down with WD 40, too much belt tension can cause this, but it rather seems like the belt pulley seizes and the engines drive pulley keeps turning causing the belt to overheat and break or stretch and come flying off.
Read Full Q/A … : Garden
Yardworks problems the belt keeps breaking on my del propelled lawn mower. i replace it and it breaks again. what could be causing it to break?
ANSWER : CHECK FOR METAL THAT IS STICKING OUT ON THE PULLY WHEN YOU FIND IT, YOU’LL HAVE TO SAND IT OFF OR USE A SANDER OF SOME SORTS TO GET IT SMOOTH AGAIN!!
Read Full Q/A … : Garden
Husqvarna mower belt on a 46 in. keeps breaking
ANSWER : I have gone to the automotive parts house and had better luck with belts for mowers and wash machines. Have you tried them?
Mike
Read Full Q/A … : Garden
When you replace the pto clutch (717-04080), does it have a tight fit with a bracket or does it have a little play.
ANSWER : There shouldn’t be any play in it. This should fit snug unless you have rubber bushings on the bracket mount to help compensate the torque of the belt engaging.
Read Full Q/A … : Garden
Let out on the break and it dies,if i keep the break on it runs great
ANSWER : Check to see if it has the right size belt.Thank you for asking and I hope this helps you.Please leave me a 4 thumbs up.
Read Full Q/A … : Garden
Drive belt Have replace drive belt but mower still has no forward movement. Mower is only 2 years old but its already had to have another drive belt installed by the dealer last year. wanted to do it myself but when i install belt theres hardly any tension so mower doesnt move. Checked and rechecked the diagram and is installed correctly. Cant find a tensioner adjustment if it has one.
ANSWER : I don’t have an answer for you, but Do you have a diagram of the Drive Belt?
Read Full Q/A … : Garden
Cub cadet lt 1050 electric pto want engage??????????
ANSWER : Make shure pig tail is hooked right
Read Full Q/A … : Garden
