Ut80993 Honda Gas Pressure Washer

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your power washer leaks water from the connection between the hose and inlet, the seal and possibly the coupling on the inlet are likely broken and will need to be replaced. This seal and coupling should be fairly easy to remove and replace.
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
Usually, leaks at the top of the hose are caused by a deteriorating washer. Before using a new hose, locate the washer and make sure it`s properly inserted into the coupling. Inspect the washer when you take your hose out of storage or put it into storage each season. Check the washers on your hose accessories, too.
The hose between your machine and the drain shouldn`t be bent or clogged. If the hose can`t remove the water properly, soapy residue may be left on your laundry. Check the hose and unclog or straighten it if necessary. The most probable cause is a clogged pump filter.
Unloader valve failure — Power lags also result from failed unloader valves. This problem can be diagnosed by manually enacting the valve function. Open the tank and drain out the air and water, then close and power back up. If the compressor bogs down once again, the valve needs to be replaced.
If your washing machine water won`t shut off, there are a few possible causes: A damaged water inlet valve. A broken water level switch. A problem with the pressure hose or air dome tube.
And when a PRV fails, it can lead to an explosion. Damaged equipment, disrupted work flow, and even injury may result. Why take that risk when you can easily tell whether or not your pressure relief valve needs replacing or repair.
An unloader valve malfunction is one of the more common air compressor issues. If the trapped air cannot escape, the accumulated pressure may be enough to keep the motor from restarting.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Soap feed The soap feed hose on my Karcher 2650 does not suck up the soap into the washer. I pulled off the connector piece that the hose is connected to. I can blow through the hose. There is a little metal finger thing that you can tell pushes up into place when the water pressure is high. It seems like it is supposed to drop down and allow some soap through when the water is running. I found a loose(attached to nothing) gasket, looks like a little donut. It was just free floating in there. I’m thinking it may go over the finger mechanism. I just put it back on top of the finger, like a halo and put the screw in piece back in. Anyway, if you know, let me know how all that goes together.
ANSWER : I fixed mine works good too, watch my video step by step i put it on youtubehttp://www.youtube.com/watch?v=UFXSLOBL0Mg

I have a deep water well, the water is brown & does not seem to clear itsself even after we let the water run for an extended period of time. The well has not been used in excess for the last few
ANSWER : Do you have a filter system..is this water going to be potable?
I would reccomend a water softener, and an iron filter for brown well water. We have used well water S Cal and Minnesota

Cub Cadet zero turn:Engine starts and runs about 5 seconds before blowing 20 amp fuse.
ANSWER : You may have a faulty voltage regualtor that is blowing fuse. Have you tried a fuse that is 5 more amps?

Culligan water filter is leaking – Culligan HF-365 Whole House Water Filter Housing
ANSWER : Turn off water
Remove filter and seal ring.
Look at mating surfaces.
Usually the cast metal has eroded away.
If it is the sealing ring , replace it. If it is the casting , replace the whole thing. Other brands may be an option.

My Husqvarna 128cd weedeater would run with choke on but not in the run position. Sometimes it would run in the run position but would not stay running. I had it running and then it cut off. I now cannot get it to crank at all. Any ideas
ANSWER : More than likely a fueling issue, wrong fuel air mix or air leak somewhere

I have a deep water well, it has not been used a lot in the last few years & the water is brown, can this problem be rectified
ANSWER : Hi Enslow, I can only guess that if the well hasn’t been in use for some time then it’s possible that if you run the pump and get brown water it may clear in time. My suggestion is simply continue to run the pump few a decent period of time that maybe a few days . As you do this take samples in say clear glass containers and see if there is improvement. So take samples every couple of hours and it will be apparent if the water is clearing or not. Make sure the pump is a decent distance from the bottom of the well.
Hope that helps
Regards
Steve

Water pump not running
ANSWER : Hi have you removed the pump from the well and tested if it will run without going via the presure switch. It could be that the pump is blocked. If it is blocked and has been for a while it may well have burnt out the pump. How deep is your well and how far from the bottom of the well is the pump. The pump should be positioned a good distance from the bottom of the well to prevent any silt getting into the pump to block it. I have a 110 meter deep well and the water level is 38 meters below ground. I have the pump at 50 meters below ground. I have only changed the pump once in 10 years.
I hope this helps
Steve

Running pump stopped
ANSWER : I assume that the plug in is working properly. Always check power supply first. Is there a GFCI circuit that it is plugged into. Then check the pump to make certain it us turning. How long had it been on before unplugging it. It could be worn out. Sometimes it takes a jolt to start the motor again. How big is the motor. Possible bad capacitor. Could be a solid state motor, then it’s bad. Is it a magnetic motor, that could be turning the wrong way.