Garden
Experienced gardeners share their insights in answering this question :
The backwash valve is not sealing properly. You need to replace the seals or the entire valve. Not knowing what type of valve you have, I can’t tell you more than that.
Try turning the valve into ALL of the operating positions and returning to filter, see if that helps.
Also, if you can easily disassemble the valve, there could be debris in it that you can remove.
Try turning the valve into ALL of the operating positions and returning to filter, see if that helps.
Also, if you can easily disassemble the valve, there could be debris in it that you can remove.
Gary
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The Main Causes of Water Filtration Leaks
With quick-connect fittings, you might find that the tube has not been fully inserted into the fitting, which can cause a leakage problem. Another common issue with quick-connect fittings includes a missing lock sleeve, which can also cause a leak in your system.
if dirt is escaping back into the pool, it could be because the filter is dirty and clogged, which means it needs to be backwashed. When the pressure gauge rises eight to ten pounds per square inch (PSI) above it respective normal operating range, backwashing is necessary.
Turn off the filter`s water supply. Check for any loose or damaged plumbing components and tighten them as needed. Check the filter housing for cracks or other damage, and replace it if necessary. Turn on the filter`s water supply to see if the leak has been fixed.
If the water filter was recently replaced, dripping from the dispenser may occur because air is trapped in the water filter.
Water should only come out of the backwash line (waste outline) when the multiport valve is set to backwash. If you notice pool water flowing out of a backwash hose when the multiport valve is on any other setting but backwash, it`s an indication of a leak.
To begin vacuuming your pool:
If you do have this option, it is highly recommended that whenever you have algae, you will need to vacuum to waste. This option allows you to vacuum the algae up and send it out through the backwash line, avoiding getting algae into your filter sand.
“How often should I backwash my sand filter”? Ensure you do it if there`s an algae outbreak or after a significant storm. A DE( diatomaceous earth)filter system needs cleaning six or more times each year. If you have a sand filter, backwash it every month and tear it down twice every year.
The wells that pump the water from the ground into the delivery system are designed to filter out sand, but some particles make it into the system. These particles typically settle in large water pipes and tanks, but sometimes make it through the faucet.
After each new filter cartridge is installed, run cold water for 5 minutes to flush it.
Can you get sick from a dirty water filter? Yes, you can get sick from a dirty water filter due to the likelihood of bacteria growth inside the filter materials. This shouldn`t be an issue if you replace the filter on time. Most manufacturers offer clear instructions on when you should replace your filters.
Well, first off, no—it`s not normal. During normal operation, your air conditioner/furnace filter should always remain dry. A wet filter is inefficient and spreads moisture throughout your ductwork and home, creating the perfect breeding ground for mildew and mold.
If your car`s air filter gets damp, your engine won`t perform as well because water will take up the space meant for air to pass through. But if you run the engine for long enough, the moisture will not harm your car or engine at all.
Standing water in the filter area
Water in this area is actually perfectly normal, useful even. It`s there to keep the seals from drying up. It drains when a cycle starts and is replaced with fresh water at the end of the cycle.
When you discover a wet air filter, remove the wet filter and dry the area up. Check the drain for debris or algae and make sure the condensate pan isn`t corroded or cracked. Turn your ac off right away, so you don`t spread moisture throughout your home. Then, put in a new fresh air filter.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Culligan water filter is leaking – Culligan HF-365 Whole House Water Filter Housing
ANSWER : Turn off water
Remove filter and seal ring.
Look at mating surfaces.
Usually the cast metal has eroded away.
If it is the sealing ring , replace it. If it is the casting , replace the whole thing. Other brands may be an option.
Remove filter and seal ring.
Look at mating surfaces.
Usually the cast metal has eroded away.
If it is the sealing ring , replace it. If it is the casting , replace the whole thing. Other brands may be an option.
Read Full Q/A … : Garden
My intex sand filter will not move water when I put the lever to filter? It will move water when I put the lever to recirc but wont move water with filter…why?
ANSWER : Im gonna guess that you stored the filter improperly off season and now the sand charge is hard as cement inside not alowing water to get thru , left alone for a week or so it might loosen up , but the best thing is to dissasemble filter and remove all sand and ck “fingers” inside this is fastest way
i allways use RV antifreeze 30/1 to store any pumps or filters off season , RV type because its nontoxic
i allways use RV antifreeze 30/1 to store any pumps or filters off season , RV type because its nontoxic
Read Full Q/A … : Garden
How to prime a sand filter pump – INTEX Sand Filter Pump
ANSWER : It depends on the pump but most pumps have a filter bowl with a screw on cover – you need to fill this with water and start the pump. if the pipework connected to the pump and the filter are empty you will usually have to repeat this process a few times, but once the pump is primed it should start up without repriming in future – Hope this helps – Nigel
Read Full Q/A … : Garden
Filter problem with hayward pool system – Hayward Pro Series Side Mount Sand Filter 30" S310s
ANSWER : You didn’t say what your exact problem was so troubleshooting with you might be difficult. Below is a link to the owners manual for these pool filters. You should be able to get your filter running properly using this.
http://www.backyardcitypools.com/images/hayward/pro-series-manual.pdf
Read Full Q/A … : Garden
My intex sand filter is shooting sand into the pool
ANSWER : You have a broken “lateral”. You will have to remove the sand from the filter, find and replace the broken lateral (pipe with slots in it in the bottom of the filter). When you are ready to refill the sand, put enough water in the filter to cover the laterals (several inches actually) to avoid damaging them as you fill.
Thanks for allowing me to assist you this evening @ FixYa.com
Read Full Q/A … : Garden
What should i have my filter on …..filter or recirculate
ANSWER : Filter and clean at back wash once a month
Read Full Q/A … : Garden
Water is not filtering right so l want to know if l connected the hose right. show me how to connect the hose from the sand filter to the pool and the motor or generator.
ANSWER : Here is a copy of the users manual for these pool filters. It has a diagram for setup that should help you know where to connect the hose. http://www.backyardcitypools.com/images/bwp/carefree-manual.pdf
Read Full Q/A … : Garden
Replaced the top gasket of the filter, turned the filter on and the water was coming out of both the pool and the backwash at the same time and the motor began to smoke. Any clue what is wrong?
ANSWER : Try consulting the owners manual for these pool filters. They have a troubleshooting guide and set up guide. It should help you know how to correct your problem.
http://www.backyardcitypools.com/images/hayward/pro-series-manual.pdf
Read Full Q/A … : Garden
