Vertical Shaft Pump MTPV93501

Experienced gardeners share their insights in answering this question :
To many things to list.
i recommend giving our free tech support person ell a call when you can be at the washer and they can walk thru the process of diagnosing it.
1-888-279-9274

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Improper inlet conditions are one of the most common reason pumps fail to produce their expect pressure. Inlet issues may also cause ongoing reliability problems. One culprit is air entrainment or lack of prime. It is important to make sure that system is designed so that liquid floods the pump to prime it.
The water pump may have suffered internal damage to a seal, bearing, or impeller. The motor will keep running but the pump is unable to develop normal pressures. “Damage” may include a broken impeller blade, scale or debris clogging the impeller or other pump components, or a failing pump seal or bearing.
The most common is improper lubrication when the incorrect lubricant is used or not enough is applied. Bearings also fail in extreme temperatures. Another cause of failure is bearing overload, e.g., a pump cavitating from lacking the proper flow will increase pressure on the impeller`s front.
Power Source If your pump has stopped working, or is not operating to the levels you expect, it could be a power issue. Look at the factory specifications for your pump and ensure that it is receiving the correct electrical power supply in order to work properly.
If the water pump is running but no fluid is being pumped this could be blocked inlet suction filter, check valves failed with pumps bypassing, blocked discharge lines, electric motor polarity is incorrect or incorrect pressure settings parameters amongst other issues.
If the water pump`s drive pulley is vibrating, the pulley bearings will wear and eventually fail. This reduces pump efficiency before eventually causing failure. Additionally, a wobbling drive pulley can cause the water pump`s impeller to become imbalanced. This will cause pump failure as well.
Turn on both the hot and cold water to about 1/8th of the way on all the faucets. Leave the water running for about two minutes. Start from the lowest faucet in the house to the highest faucet. This allows the water pressure of the system to force all of the air from the pipes and out through the faucets.
Restricted airflow/a dirty coil will cause high head pressure, the same way that a dirty outdoor coil will cause high head pressure in cooling mode. Be sure to also check filters and make sure that register grilles have not been closed off in certain rooms. Take pressure readings at all three ports on the outdoor unit.
For a single level home or a two story home without water fixtures on the 2nd floor a 30/50 PSI setting may be sufficient. For two or more levels with water fixtures on more than one level you may want to use 40/60 PSI setting. It`s easier for a pump to supply the lower pressures and it`s less strain on old plumbing.
Low water pressure often means water lying in your pipes as the pressure can`t force it through. And unfortunately, when this happens, rust can occur. Corrosion is also a common factor in older pipes. Over time, the metal reacts with the water to cause a build-up of rust deposits.
First, you can increase the fluid flow rate into the pump. This will increase the pressure on the fluid, and therefore increase the output pressure of the pump. Second, you can increase the displacement of the pump.
A clogged suction pipe: If a suction pipe is riddled with debris, there is less flow into the pump, which in turn leads to less flow out of the pump. Worn impeller, ring, and plate: If the vanes on the impeller, the ring, and plate have worn down, the hydraulic capacity of the pump is hampered.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

This pressure washer will continue to build pressure when you let off the trigger. I have replaced the hose 3 times because the pump continues to pump until it blows the hose. The pump will not stop pumping!
ANSWER : You have a defective pressure release valve or someone has misadjusted.

Read Full Q/A … : Vertical Shaft Pump MTPV93501

I have a 1/2 horse wayne shallow well pump. At times the water in the house slows to a trickel. This will happen for about 40-120 seconds then the pump seems to kick on and the pressure is restored. I have replaced the high low switch and the problem persists. Please let me know any thoughts on the problem. Thank You
ANSWER : Check air in your water tank should be less than you’re cut in pressure..

Read Full Q/A … : Vertical Shaft Pump MTPV93501

Lost high pressure
ANSWER : Piston rings defective. Replace. Possibly scored cylinder walls that may need to be resurfacing or replaced.

Read Full Q/A … : Vertical Shaft Pump MTPV93501

Ex-Cell EXPRO2530 w/Cat Pump. Pressure builds and stalls engine.
ANSWER : Your unloader valve is not wotking, get a diagram of the pump from cat and it will show what parts you need to replace, or check for blockage in the valve.

Read Full Q/A … : Vertical Shaft Pump MTPV93501

Oil appears to have come out of the oil filler cap. Is this a sign of overfilling the oil, or something else?
ANSWER : Id definitley say its over filled. try checking the dipstick

Read Full Q/A … : Vertical Shaft Pump MTPV93501

My pressure washer will start for a second and then shuts down. I just bought it from a friend and don,t think the springs to the govner are right but not sure.would like a skicamitc of the engine or manual so i can see if they are right
ANSWER : When you start your engine open wand trigger this will probably allow you to get the engine warmed up and I think it’ll work for you it used to work for us .

Read Full Q/A … : Vertical Shaft Pump MTPV93501

What oil do i use in the pump? The oil is milky and needs changing.
ANSWER : Well you can use direct recommended from Ace Hardware see link.

http://www.acehardware.com/product/index.jsp?productId=1340266

They recommend 250 hours, but i’d change more often, like you said when it’s milky. If it begins to get water in the oil sooner, that indicates your piston to crankcase seal is beginning to leak.

Read Full Q/A … : Vertical Shaft Pump MTPV93501

I have a pressure booster pump installed which turns on automatically when we open the tap and turns off by itself when we close the tap, but when power goes and comes back(common in india), the pump will turn on even with no tap opened and does not turn off automatically and goes on running, some kind of airlock problem I think, when we just shut off and on water input several times, it again starts working well
ANSWER : Check to see if the output pipe has water in it when the pump swutches off the pump needs to be primed at all time what we normally find cases like this is the pump is higher than the supply or there is an air pocket on the output where the pressure sensor is

Read Full Q/A … : Vertical Shaft Pump MTPV93501