Sears
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Certified Snowblower RePlacement Auger Belt, 3/8 x 34.4-in.
Murray Replacement 1/2-inch X 38.1-inch Auger Belt Drive.
An easy way to determine belt size is to simply “add 2″ to your off-the-rack trouser size. For example, if you wear a 36” waist trouser, then a 38 belt size will be a safe bet. Most will find this simple formula works best for pants worn at a traditional height–close to the natural waistline.
It comes as a match set of belts that are 3/8-inch top width x 35-inch long.
Cables do stretch over time. Performing these adjustments will tighten any slack that may have occurred due to stretching. It may be necessary to inspect and possibly replace one or both belts. These belts operate the drive systems for the wheels and the auger.
Introduction. Snowblower belts start to wear out after 5 to 7 years, and should be replaced. You can save money by doing the job yourself.
Single-stage snow blowers typically have a clearing width somewhere between 18 and 21 inches and tend to have an intake height of no more than 13 inches.
The effective length is obtained by adding the effective outside circumference of one sheave to twice the center distance between the two standard measuring sheaves at the standard measuring tension.
Carefully centre the belt and pull down on the movable pulley until the belt is taut. Pull the belt as tight as possible for a good reading. On the scale underneath the moveable pulley, the outer lines on the blue plastic will indicate the length of the belt in millimetres and inches.
For most two stage snow blowers, there are 2 or 3 belts under the cover. One belt will drive the auger, and the other will drive the wheels.
42 In. Deck Drive Belt | CRAFTSMAN.
The first digit indicates an eight-rib belt, followed by “P” to identify metric belt sizing, and a “K” showing that this belt conforms to the SAE standard for rib sizing (3.56 millimeters wide for automotive-type serpentine belts). The final series of numbers is the effective length of the belt, given in millimeters.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Mtd 31c won't stay running? – MTD Genuine Factory Parts Auger Belt for One-stage Snowblower
ANSWER : You probably have to take the carburetor apart and clean it using a spray type carburetor cleaner spraying the jets and small holes in it.
Read Full Q/A … : Sears
I need the belt diagram for a 42″ craftsman 20.5 hydro tractor
ANSWER : Do a model search on www.partsdirect.com. This is the website for Sears equipment. Just reminder you will need the model number from under the seat to help you find the right model.
Read Full Q/A … : Sears
Mower belt diagram – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : You can get a belt diagram from
sears.com
just follow the leads, and have your model number handy, you will need it.
you can also get this from ayp.com
Read Full Q/A … : Sears
I have Remington REM55PV heater. It starts just fine but when I take finger off ignition button, heater won’t stay running.
ANSWER :
Read Full Q/A … : Sears
I need to replace springs on mower deck of a craftsman LT1000 does sears carry replacement springs or can i go somewhere else
ANSWER : If you have the parts to the old one you can match it up at a hardware store but try sears online www.searsparts.com but shipping will be as much as the part
Read Full Q/A … : Sears
What is the diagram for traction belt routing
ANSWER : Go to this website, upper right hand corner and do a parts look up.
Search for your model and that good stuff they ask of you and then
choose mower housing should be there, browse the site it’s really cool
and has a lot of info. http://www.jackssmallengines.com
I did a
sample search for generic riding mower deck and found great diagram of
belt routing. Give it a try you will find same results Good Luck! Don’t forget the thumbs!
Search for your model and that good stuff they ask of you and then
choose mower housing should be there, browse the site it’s really cool
and has a lot of info. http://www.jackssmallengines.com
I did a
sample search for generic riding mower deck and found great diagram of
belt routing. Give it a try you will find same results Good Luck! Don’t forget the thumbs!
Read Full Q/A … : Sears
Im looking for part # for auger belt &drive belt for mastercraft 8/26 snowblower model #319-586-515
ANSWER :
Read Full Q/A … : Sears
What is the part no. of the blades on a 42 in. mower
ANSWER : You can go to Sears’ website at www.partsdirect.com and enter your model # (usually found under the seat) to view the diagrams for your model and locate your part #’s. Once you find the Sears #’s, you can find replacement blades for your mower at Partsbuggy’s Sears page here – http://www.partsbuggy.com/ope/ayp_roper_searsmower_parts.htm. It also lists Sears’ part numbers along with the blades and belts by deck size.
Read Full Q/A … : Sears
