Garden
Experienced gardeners share their insights in answering this question :
Chains saws are 40:13.2 ounces 2-cycle engine oil for gallon gasoline
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
All STIHL gasoline-powered equipment uses a 50:1 gas and oil mixture.
The fuel and oil mixture should always be 2% (50:1).
THE RIGHT FUEL AND OIL RATIO FOR YOUR STIHL PETROL TOOL
1:25 = 1 part oil + 25 parts petrol, or 40 ml oil per litre of petrol when using other brands of oil.
Always use quality two-stroke engine oil complying with the TC classification. It is best to use STIHL two-stroke engine oil which is specially formulated for STIHL engines and helps to prolong engine life.
Only from STIHL – This patented 50:1 fuel mixture combines non-ethanol, high-octane fuel and premium STIHL HP Ultra Oil.
For a mixing ratio of 1 : 50 you need 5 litres of high-octane gas and 0.10 litres (100 ml) of STIHL two-stroke oil.
Use a 40:1 two-cycle oil mix ratio. One gallon of gasoline combined with 3.2 oz of two-cycle engine oil. Unsure of the age of your equipment?
For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas. For a 40:1 mixture, use 3.2 fluid ounces of oil per gallon of gas.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
What kind of oil in the oil tank and how much for the remington electric pole saw ?
ANSWER : Bar & chain oil is the best. You can use regular or synthetic. Some say you can use atf (auto transmission fluid) or sae30 oil. I use bar & chain oil.
Read Full Q/A … : Garden
My 290 isn’t oiling chain. I tried adjusting oil flow and still no oil?
ANSWER : You have to remove the bar and clean it out
Read Full Q/A … : Garden
Is 10-30w car oil ??? Okay to use as the Oil on the Chainsaw Bar of a Remington Pole Saw Model 106890-02?
ANSWER : Car engine oil has not got a non fling addative so will just spray off the end of the bar and not lubricate the chain where it does most of its cutting, on the underside of the bar.
Read Full Q/A … : Garden
16″ Electric Chain Saw: what kind of oil is used for electric chain saw…
ANSWER : I assume you are asking about the oil for the chain. Any good quality “Bar and Chain Oil” will do fine. Do not use motor oil you use in your car engine as it will not properly lube the chain and will result in quicker dulling and early demise of the chain.
You can get the “Bar and Chain Oil” at most hardware stores or Farm Supply stores.
Read Full Q/A … : Garden
Every chain saw uses as fuel a mixture of oil and gasoline. What is the correct mixture for a textron gasoline powered saw?
ANSWER : 25:1 to 32:1 Start at 25:1. If it smokes too much or fouls a plug, go to 32:1 using a good grade 2-cycle oil.
Read Full Q/A … : Garden
Lost my manual what type of oil and what capacity
ANSWER : Any chain saw oil from your stockist…saw oil is saw oil.remington made many saws.
Read Full Q/A … : Garden
What type of oil do I use for pole saw? – Remington Polesaw Wizard
ANSWER : Use bar and chain oil (bar oil is SAE 30 with an addative to make stick to the bar and chain) available at home centers and hardwares. Excerpt from a Remington OM follows:
“FILLING OIL TANK
1. Remove oil cap.
2. Fill oil tank with SAE #30 motor oil.
Note: For temperatures below 30°F, use SAE #10 oil.
For temperatures above 75°F, use SAE #40 oil.
3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank.
4. Wipe off excess oil.
Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage.”
“FILLING OIL TANK
1. Remove oil cap.
2. Fill oil tank with SAE #30 motor oil.
Note: For temperatures below 30°F, use SAE #10 oil.
For temperatures above 75°F, use SAE #40 oil.
3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank.
4. Wipe off excess oil.
Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage.”
If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou
Read Full Q/A … : Garden
My 18 Inch chain saw will not keep oiling the Chain, I had it worked on and He said it was plugged. How do you unplug it with out taking it all apart. Is there a spot to blow air through. the Preacher..
ANSWER : Remove the chain bar and look just below the bolts holding it in place. You’ll see a small hole where the chain bar oil pump pushes out oil. Make sure this hole is clear then run the saw without the bar on.
Be CAREFUL of fingers!
You should see oil coming out of that hole. If not, you may need more serious work done with the saw (chain bar pump replacement).
Read Full Q/A … : Garden
