Pro Chain Saw 46cc 20″
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
A single fuel pipe runs from the tank, under the floor of the car to a mechanical pump on the engine. The pump delivers fuel to the carburettor. Whenever you check fuel pipes, disconnect the battery to prevent stray sparks igniting petrol or petrol vapour.
A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio. Over a period of time oil will separate from gasoline.
The return line should direct fuel close to the bottom of the tank and away from the pickup.
The (clear) fuel intake line runs from the top of the carburetor (straight nipple) and goes to the short post on the back of the primer bulb. The return line (blue) comes from the long post on the back of the primer bulb and goes into the bottom of the fuel tank.
Most vehicles have rubber fuel hoses connecting the fuel pipes on the chassis to the fuel pump or carburetor on the engine. Rubber hoses are flexible and can be cut to length as required, but they have a tendency to perish over time and can rub through if not properly secured.
Most vehicles have rubber fuel hoses connecting the fuel pipes on the chassis to the fuel pump or carburetor on the engine.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Replaceing fuel line in polan 3300 chain saw – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Hi owjbhend…
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up
Use a piece of wire and insert it into the fuel line, then bend a hook in the end and hook it over the end of the fuel line…lubricate the fuel line with some vaseoline very lightly…about the first one inch of the fuel line and then use your fingers to start the fuel line into the tank, once you have the fuel line in the tank give enough to hook the fuel filter to and so it can be dropped back into the tank.
Below is a drawing of how to route the fuel lines.
Please take time to rate me thumbs up
Please take time to rate me thumbs up
Read Full Q/A … : Pro Chain Saw 46cc 20″
Saw starts runs good for a while then quits – Poulan Pro Chain Saw 46cc 20"
ANSWER : Try this out. I have the same issue. When its acts like it wants to quit, crack open the fuel cap. The cap has a small breather in it and if that gets clogged it will starve fuel.
Read Full Q/A … : Pro Chain Saw 46cc 20″
Change the chain instructions – Poulan Pro Chain Saw 46cc 20"
ANSWER : General instructions are, if the machine has a chainbrake make sure this is off, loosen the side cover nut/nuts, wind the bar adjuster screw back to slacken the chain, remove the side cover, push the bar back to the sprocket, the chain should now be lose enough to lift it off the tip of the bar and un loop off the sprocket, now loop the new chain over the sprocket and around the tip of the bar, make sure the cutters on the top of the bar are facing away from the saw ( a pushing chain )now re fit the side/chainbrake cover, if the bar adjuster pawl is in the brake/side cover, make sure this aligns with the adjuster hole in the bar, re fit the bar nut/nuts finger tight, wind the adjuster screw in so as the chain sits snuggly all around the bar, with a gloved hand pull the chain around the bar manualy, it should pull smoothly, lift the tip of the bar up and fully tighten the nut/nuts, run the saw, there will be an amount of initial stretch, slacken the bar nut/nuts and re tention.
Read Full Q/A … : Pro Chain Saw 46cc 20″
Why my poulan saw excelerates on its own and stalls when I squeeze the trigger
ANSWER : Needs low speed needle on carb turned counter clockwise half turn.
Read Full Q/A … : Pro Chain Saw 46cc 20″
I have a poulan 305 pro chain saw were do the 2 fuel lines go?
ANSWER : Find your model nuber here:
Poulan.com
http://www.ordertree.com/modelinfo/POULAN-WEED-EATER/75.59.html
The drawing containing your fuel system is as good as it gets. If you need more help contact PoulanPro.com. HTH
Lou
Poulan.com
http://www.ordertree.com/modelinfo/POULAN-WEED-EATER/75.59.html
The drawing containing your fuel system is as good as it gets. If you need more help contact PoulanPro.com. HTH
Lou
Read Full Q/A … : Pro Chain Saw 46cc 20″
How do I replace the fuel line for a Poulan ppbp30?
ANSWER : Open the top of the machine to access the carb, Normally it is easily done with needle nose pliers.
Read Full Q/A … : Pro Chain Saw 46cc 20″
My Poulan Pro 295 chain saw starts fine, runs for a few minutes, then stops and will not start until completely cool. What could be my problem?
ANSWER : It sounds very much loke the ignition is playing up when hot, just as a little test when it starts to die slacken off the fuel filler cap does it pick up/re start? if yes it is a fuel tank breather issue, replace the breather.
Read Full Q/A … : Pro Chain Saw 46cc 20″
Chain won’t stay tight on my poulan 222 pro. I have the correct chain size. Does the bar need to be replaced?
ANSWER : No, the bar fasteners are not tight enough. If the saw is under warranty, take it to a servicing dealer for repair or instructions to correct what you are doing wrong. Good luck!
Read Full Q/A … : Pro Chain Saw 46cc 20″
