Excalibur Gas Hedge 22″ Trimmer Blade

Experienced gardeners share their insights in answering this question :
You should be able to sharpen your hedge trimmer blades. There is a good video on how to sharpen hedge trimmer blades on youtube by ereplacementparts. He explains how to do it with a file or a grinder.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Hedge trimmer blades can be sharpened by hand, and it is recommended that you do so regularly: the job needs a flat file, a whetstone and a little careful attention. Alternatively, your STIHL dealer can sharpen the blades perfectly for you.
Blades should always be replaced in sets. A blade set consists of one moveable top blade and one stationary bottom blade. It is highly recommended that you keep at least one set of blades for each type of working tool in your shop.
In general, it is recommended that you replace your hair clipper blades every three to six months.
Over time, all blades eventually dull and need to be sharpened for optimal performance. Your hedge trimmers are no different in this respect. Regardless of whether you use them sparingly or often, you`ll need to sharpen them.
It`s not necessary to lubricate the blades of a hedge trimmer to prevent rusting because they are pre-hardened rust resistant steel. However, you can use a lubricant to clean the blades, we recommend a light spray on lubricant such as WD-40 to give a thin coating.
For best operation and longer blade life, lubricate the hedge trimmer blade with a lightweight machine oil before and after each use.
You made need to squeeze the sheath with your finger and thumb and allow air to enter the cover in order to disengage the sheath from the teeth of the blade. Please refer to your owners manual for assistance.
You made need to squeeze the sheath with your finger and thumb and allow air to enter the cover in order to disengage the sheath from the teeth of the blade. Please refer to your owners manual for assistance.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Weedeater Excaliber Gas Hedge Trimmer. Is it possible to sharpen these blades? If yes, do you know the procedure?
ANSWER : You should be able to sharpen your hedge trimmer blades. There is a good video on how to sharpen hedge trimmer blades on youtube by ereplacementparts. He explains how to do it with a file or a grinder.

How do you sharpen the hedge trimmer. It is the homelite handy hedge 2.7 17 inch blade
ANSWER : DREMEL STONE WORKS THE BEST. THEY SUGGEST TO REPLACE BLADES

Blades wont move when power connected. Stripped it down. Motor is fine. I think it must be the gears attached to the blade unit
ANSWER : Either the gears, OR SOME machines have a “CENTRIFUGAL CLUTCH” [a safety feature] between the engine and the blades.

IF your machine has this feature, then it’s possible that the clutch has worn out and is slipping so badly that the blade won’t move.

Not cutting properly. blades seem to be out of sync.
ANSWER : Hi
try to spray oil the blades
if not helping
take the machine to be seviced you might need to sharpen the blades.

How do I sharpen this weed eater excaliber hedge trimmer blade?
ANSWER : Took mine off yesterday… need to sharpen or buy another? Neal

Baldes locked up – Remington At3017b Hedge Wizard
ANSWER : Ensure blades are sharpened. If there are burs on blades they can seize.Blades should be lubricated with WD40 , waste oil or other lubricant.The bolts holding the two blades together shouldn’t be too tight.

Engine runs great, accelerator responds perfectly, but the blades stopped moving. Any ideas?
ANSWER : Ensure blades are sharpened. If there are burs on blades they can seize.Blades should be lubricated with WD40 , waste oil or other lubricant.The bolts holding the two blades together shouldn’t be too tight.

How to sharpen stihl gas power trimmer
ANSWER : Sharpen with a flat file. Its a long process as each tooth has 2 cutting edges. There are companies that will do this properly at cost.