Annovi Reverberi

Have xvm2.5g26 pump.when I turn water supply on,water drips out of detergent port,when engine is stsrted,water flows heavier out port.When left idling engine will hunt every 10-15 sec. Will not hunt when trigger is pulled. Water continues to flow heavier weither idling or gun pulled. rebuilt detergent valve no help. Thanks,Deron
Experienced gardeners share their insights in answering this question :
Detergent valve is ball bearing and spring. make sure its clean and the right way around and damage free.hunting can be caused by incorect idle, and is normal if machine is building up pressure when not being used.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Detergent can gradually build up in the detergent tray and its attachments over time. If these are not cleaned regularly, the water and additives will not dispense fully and water will remain in the compartments.
If your power washer leaks water from the connection between the hose and inlet, the seal and possibly the coupling on the inlet are likely broken and will need to be replaced. This seal and coupling should be fairly easy to remove and replace.
If your pressure washer starts and runs fine, but there`s no pressure or no water coming from the pump, it could be a clogged wand, hose or inlet filter. Fortunately, this is an easy pressure washer problem to repair. Begin isolating the problem by hooking a water hose to the washer`s inlet and turning it on.
A small amount of water remaining in the dispenser at the end of the cycle is normal. Try cleaning your fabric softener dispenser to remove any blockages. If liquid left in a dispenser is at MAX level at the completion of the cycle, check for and remove any blockages.
Hold the soap drawer under a tap, and allow water to fill the fabric compartment to overflowing… … When you turn off the tap, hold the drawer steady and level. The remaining water should slowly siphon up and out of the hole under the cap and run out from the bottom of the drawer.
Usually, leaks at the top of the hose are caused by a deteriorating washer. Before using a new hose, locate the washer and make sure it`s properly inserted into the coupling. Inspect the washer when you take your hose out of storage or put it into storage each season. Check the washers on your hose accessories, too.
Over Use of Detergent

Rather than a part being damaged or broken, leaks can also occur from adding too much detergent to your washing machine. Oversudsing can happen throughout the entire washing cycle but can be well seen during the emptying stage. Avoid using too much, or high-sudsing, detergent if this happens.

Try a soft reset, by pressing power button for 12 seconds and then power on the device. If your soap dispenser isn`t used for a prolonged time, soap can accumulate and clog the nozzle. To troubleshoot, clean the nozzle area with water and remove any stuck soap.
Provided that the soap itself hasn`t run out, the most common reasons for this may be: If your dispenser has not been used in a long period of time it may become clogged. The sensor may be damaged, the batteries have run out or the wiring is faulty (in the case of automatic soap dispensers).
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
In general, most pressure washers can draw water from any source like a water tank with a minimum of PSI of 20 to work properly. Some pressure washers can also work fine even with lower pressure since most have built-in pumps that push the water out of the nozzle with high pressure.
One of the most common causes of a detergent drawer not emptying is blocked jets. These are the tiny holes at the top of the compartment where water is sprayed into the drawer to flush the contents through.
Liquid laundry detergents, in non-concentrated form, are made up of 60 to 90 percent water.
Water is the main ingredient in liquid laundry detergent. Water is heavy to transport and shipping adds to consumer and environmental costs. Liquid detergents limit the effectiveness of some cleaning ingredients, like oxygen bleach, because they are not stable for long periods of time when mixed with water.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Poor pressure and water comes out of the detergent hose
ANSWER : Replacing the wand wont solve the pressure problems, its going to be the pump problems, pump create high pressure to the wand. hope that help

Read Full Q/A … : Annovi Reverberi

I have a Northstar pressure washer powered by a honda GC160 engine. The last time i used it, water leaks from the bottom of the unit, whether it is running or not. When running, the pressure is fine. I have felt underneath and it appears that the water is coming from the second opening from the rear. Is there a pressure relief valve there. I have a manual but cannot find any descriptors for underneath the motor.
ANSWER : This is a piston seal issue. You can get a kit to rebuild the pump.

Read Full Q/A … : Annovi Reverberi

Culligan water filter is leaking – Culligan HF-365 Whole House Water Filter Housing
ANSWER : Turn off water
Remove filter and seal ring.
Look at mating surfaces.
Usually the cast metal has eroded away.
If it is the sealing ring , replace it. If it is the casting , replace the whole thing. Other brands may be an option.

Read Full Q/A … : Annovi Reverberi

Water will not come out of sprayer – Karcher G 2600 VH Gas Pressure Washer
ANSWER : Either the checkvalves closed on the inlet or the chemical injector on the output may be clogged they will have to be removed for inspection.

Read Full Q/A … : Annovi Reverberi

Couple of guys tried to help me on this, perhaps you guys could come back. I forgot to mention there is a pressure tank bladder type on the discharge side. Could the air in this tank be messing with the prime. I checked the intake. It has water in it after bleeding air from the discharge system where before it was dry before purging air. I think there is air in the system and wonder if it is coming from the pressure tank?. i open up one of the discharge valves and a lot of air comes out. Should I put a valve on the pressure tank to take it off line until I get water from the well?

Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve but I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
I disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling water. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.
I took the pump nose off and looked at it. The one way valve appears to be working fine. The impeller is working fine also evidenced by when I turn it on witht the discharge cap off, water shoots out. When I open one of the discharge valves and turn it on, the pressure drops to 10lbs. At this point the prime water has moved through the pipe and and the pump does not soound like it has any water in it. I pull the cap off and have to “reprime it again.” It again goes back to the pressure gauage rapidly fluctuating while pump on. I disconnect pump on intake side I hear no vacuum. The guage is on the discharge side. The seals on the pump nose do not look frayed or damaged. The pump is not leaking water in any of the joints. The pipes on discharge and well side do not appear to be leaking.

ANSWER : My friend, please boil your question down. Your title has to do with riding mowers but the leaking, bladder, impeller, air bubbles, pressure tank, check valve comments seem to be migrating toward a pump of some kind – well? spa? pool? irrigation?

Briefly, any system that involves a water source, a water moving device, water storage device and ultimate useage is subject to leaks … into the system and out of the system. If this is a well and you have air in your system, your pump may be sucking air at the well or any loose connection between the tip of the pipe and the inlet to the pump. Your bladder could have failed but from what I can get from your comments, this is not the case. On the pressure side, neither air nor water will leak in … only out.

Please recheck all connections. Make sure your check valve is installed correctly and not leaking. The check valve assists the foot valve, which may have failed.

I am more inclined to think your well may be at the end of its useful life. To prove or disprove, you could have a plumber put a vacuum gage on your pump. He or she can answer this question is about 90 seconds based on this test. Expect to pay for one hour of time, which will be less than the time you have already invested in your project.

Read Full Q/A … : Annovi Reverberi

No pressure , no water coming out, does the system need bleeding if not used for several months
ANSWER : YES. THE PUMP WILL NEED BLEEDING IF IT HAS NOT BEEN USED FOR A WHILE.

Read Full Q/A … : Annovi Reverberi

I loaned my K2.55 to somebody else and it is now heavely leaking just above the detergent housing element. It appears to come from under the metal cover (visible after I removed the plastic housing)

I want to send you a picture. How can I send that to you?
Ed

ANSWER : Ed,If you can send over a picture of where this leak is at I can advise you as to how to fix the problem. See contact info below. From your description it sounds like the leak is coming from behind the head of the pump which is commonly caused by failing water seals around the pistons.Sincerely,Aron KerrLanda [email protected]

Read Full Q/A … : Annovi Reverberi

Why doesnt my powerwasher pump out water
ANSWER : Check for a blocked jet in the end of the wand ( squashed hoses or blocked hose to the wand)
the blocked jet has the same affect as not pulling the trigger and the pressure regulator bypasses the water back into the pump

Read Full Q/A … : Annovi Reverberi