Garden
B&S xte 50 what fuel 2 stroke or unleaded
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Victa Formula V 2 Stroke High Performance Motor Oil (fuel oil ratio 50:1) 100ml of Oil to 5 Litres of Unleaded Fuel. Congratulations on your purchase of a top quality Victa lawnmower.
For the 4 stroke engines 600ml of SAE 30 oil must be placed in engine sump before starting engine.
Use a 40/1 ratio on the Victa or it will sputter and die let it warm up with choke on and slowly increase revs until good Togo turn choke ok once running ok.
Fuel for your lawn mower or outdoor power equipment must meet these requirements: Clean, fresh, unleaded. A minimum of 87 octane/87 AKI (91 RON); If operating at high altitude, see below. Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary butyl ether), is acceptable.
2-stroke engines are generally used in handheld lawn equipment because the power per weight is greater than 4-stroke engines; this means that a smaller engine will pack more power than a smaller 4-stroke engine.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Fuel mix oil to fuel ratio
ANSWER : The oil ratio is 50:1
Here is the website: http://homeguides.sfgate.com/oil-fuel-mixture-farm-tough-husqvarna-chainsaw-83933.html What Is the Oil Fuel Mixture for Farm Tough Husqvarna Chainsaw
Here is the website: http://homeguides.sfgate.com/oil-fuel-mixture-farm-tough-husqvarna-chainsaw-83933.html What Is the Oil Fuel Mixture for Farm Tough Husqvarna Chainsaw
Read Full Q/A … : Garden
Why will my1994 bravada not start?
ANSWER : Very possible your new pump went out again, or was not installed correctly. Check fuel pressure. If you know electrical you can jumper the relay to run the pump. On some GM models I have seen a test wire for the pump underhood.
Read Full Q/A … : Garden
1999 ford expiodition
ANSWER : Use a pressure gauge to check pressure at the rail. Change fuel filter. Replace fuel pump if needed.
Read Full Q/A … : Garden
Fuel mix 1.40 or 1:50? – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : This is usually dependant on the two stroke oil quaility, good quaility two stroke oil from a major chainsaw manufacture will normally be advised to mix at 50.1, always try to buy good two stroke oil, from a chain saw manufacturer, they know the importence of oil quaility on high reving two strokes.
Read Full Q/A … : Garden
What is fuel mixture for solo motosage 60135
ANSWER : Some say 100:1 with synthetics. I use synthetics on 80cc and larger saws in the range of 40/50:1. I never go higher than that….saws are just too expensive to be stepping over dollars to pick up pennies. A lot of people are trying to make mixing ratios like some kind of mystery voodoo. You’ll always be fine in the 40/50:1 range with a good synthetic oil.
Read Full Q/A … : Garden
Where can I find parts for this Tornado Pressure Washer P/N 36010?
ANSWER : Salvation Army, Craigs list, E-bay but even better, if you find out the cost is too much, buy a new one from amazon, they have an awesome sale on it:
2000LB Pressure Washer
2000LB Pressure Washer
Read Full Q/A … : Garden
Fuel Ratio Fuel mix ratio for Homelite (chainsaw) ut # 10520a
ANSWER : 40:1 is about right. Be sure to use modern synthetic oils made for saws and premix thoroughly before adding to the saw.
Read Full Q/A … : Garden
Have a craftsman 16″ chain saw 358.360260. Could not initially get it started after it had sat for a couple years with fuel stabilizer in it. When I went to use it the fuel had all evaporated and the fuel pick line was rotted. I replaced that with some difficulty but finally got it on. Saw still wouldn’t start. Replaced the fuel filter. Still wouldn’t start. Pulled the carb apart and cleaned and recleaned everything. Diaphragms were good and I didn’t adjust any of the mixture screws because as I said it ran fine before storage. Non of the carb passages were clogged. Fresh gas 40:1, good spark plug and good spark. Airfilter is good. Engine has maybe about 4 hours of total run time on it. It’s a ZAMA (?) carb. It will run for about 30 seconds when I manually prime it by pouring a small amount of fuel directly though the carb. When I was disassembling the carb the vent hose that goes back into the fuel tank seemed to have a small out of ?substance? in it which I cleaned out. It was right at the end the of the hose that goes back into the fuel tank and not up by the carb. It didn’t appear to be like your typical gummy deposits/varnish though. I hope it wasn?t some type of spongy check valve stuff that is supposed to be in there. That might explain some of my problems. Anyway, I also can not seem to get the primer bulb to fill. When I open the fuel tank, look in side and depress the primer bulb, air bubbles come out of the fuel filter. But when I let the bulb reexpand there’s no fuel that gets sucked up the hose. I can however seem to fill the primer bulb when the fuel tank is full and the chainsaw is laying on it?s pull cord side and the bulb is depressed a bunch of times. The saw will also start and run again for about 15 seconds then die. It’s definitely not getting/fuel and probably running out . Thanks.
ANSWER :
Read Full Q/A … : Garden
