350 18 Inch Gas Chainsaw 52CC Fully Assembled Brand New 18″

Experienced gardeners share their insights in answering this question :
There should be a safety bad on ths handle that you hold down so that you can pull the throttle trigger. Check to make sure you are depressing it enough or that it is actually unlocking when depressed.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your Stihl chainsaw starts up with a reassuring puttering sound, but dies when you pull the throttle trigger, there likely is an issue with the fuel, but the carburetor could need adjustment. If the saw stalls while it`s idling, it`s almost surely a misadjusted carburetor.
Check the air filter and spark plug on the Husqvarna 350. If the air filter is clogged or dirty, clean it or replace it with a new one from Husqvarna or an online parts house. You can test this by trying to start the saw without the air filter. Some parts houses offer maintenance kits that include the filter.
If the chainsaw won`t start, or starts and then stops and you find the spark plug wet with fuel mixture, it means that the engine is flooded (you will probably smell petrol). It happens when too much fuel enters the combustion chamber, possibly because you have pressed the primer many times.
Over time, the spark arrestor can become clogged with soot. If the spark arrestor is clogged, the chainsaw may run stall or run rough. To unclog the spark arrestor, remove it and clean it with a wire brush. You can also replace the spark arrestor.
The engine throttle is operated by the trigger under the rear handle of the saw. Unless the lock-out switch above the rear handle is also pressed, the throttle cannot move from the idle position, and the chain will not be driven.
If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged. If this is the case, clean it with a wire brush.
A dirty carburetor, bad gasoline and low-quality two-stroke oil that creates deposits all contribute to chainsaw starting problems.
If your chainsaw does not start, the fuel may be too hot. To prevent this from happening, always use fresh fuel and reduce your operating time when the weather is warm. If your chainsaw will not start, place it in a cool area away from sunlight for at least 20 minutes.
The most common cause of a chainsaw that won`t cut properly is a dull cutting chain. Try sharpening or replacing the chain. Need help finding your model number? The chain may not have the proper amount of tension.
If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
My chain saw starts and then dies what is wrong? This could be a number of things and is most likely fuel or storage related. Over a short period of time, fuel will become stale. If the unit is stored with stale gasoline, the system will become clogged or restricted.
My chain saw starts and then dies what is wrong? This could be a number of things and is most likely fuel or storage related. Over a short period of time, fuel will become stale. If the unit is stored with stale gasoline, the system will become clogged or restricted.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My dog tore out some wires on lt1000 17.5 hp ridng mower. inow have it wired so it will start and run,but have one wire i dont know where it goes. from the ignition switch the blue is hot the black im not sure. there is an orange wire that i assume keeps the battery charged just dont know where it goes. after mowing mower will not restart. is there a wiring diagram?
ANSWER : Orange wire goes on the A2 terminal on back ignition witch.

Looking for a wiring diagram for a ford 9n tractor, Messed up wiring on old tractor when trying to tune it up. Now may have the wiring messed up at the fuse link on the back of the dash
ANSWER : Try this website if you do not get help here:mytractorforum.comYou will have to register to ask questions, but there is a good chance that you will be able to find what you need already posted there. Good Luck.

What are the settings for the zama carb on a 330 homelite chainsaw
ANSWER : 1 1/4 turns out. Then let it warm up and adjust in up to 1/8

Carb screws need adjusted i need to know the settings
ANSWER : Hi. Lightly seat the low screw and bring it out one and a quarter turns. Lightly seat the high and bring it out one turn. Adjust idle screw to suit. Regards Phil.

2375 ”wild thing” poulan saw hard starting after carb rebuild
ANSWER : Through trial and error on fairly new Poulin Pro, found that the usual 3-half turns for both high and low was too much (flooded) (Used to be good starting point on weed eaters years ago. So, turned both all the way in, and only backed out 1-full turn. (2-halves) Saw fired up perfectly, and ran wide open just fine. Try that.

Need a wiring diagram for a StaRite water pump 220V/110V with capacitor.Using a110V supply
ANSWER : Sta-rite pump is humming and no water

Where can I get a wiring diagram for cub cadet 2550?
ANSWER : Go to mtd cub cadet . com and they will have a schematic

All wiring disconnected need wiring diagram – Simer 1 Hp 230 Volt 3 Wire Submersible Well Pump, 4"
ANSWER : Http://www.simerpump.com/pdf/SIM280.pdf

This is a full manual, check your model number, though.

Gary