[SOLVED] Trigger Switch On My Marksman Mitre Saw Has Shorted Out And Am Unable To Read Part Number.No Success In Contacting Marksman Direct. Machine Nu...

mber 66072c 255mm 1800w 4600rpm PA6-GF30.
5 connection switch.
Any information on locating a replacement would be appreciated
Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If the laser on your miter saw won`t turn on, the most likely parts that could be causing this are the switch, laser, power supply assembly, and adjustable laser guide. With help from us, you can fix have your miter saw yourself, saving you on time and money.

There are several reasons your miter saw may not be cutting straight. The blade is warped, damaged, or not installed correctly. The bevel gauge on the miter saw is misaligned. The miter gauge is misaligned.

If the motor is spinning, but the blade is not, the first thing to check is the belt as they wear out and break. You can inspect the belt by removing the belt cover. If the belt is broken, remove it and install a new one. On some models, you will have to walk the belt onto the pulleys.

Look out for accumulation of saw dust; it can stop you from reaching the full deep. There`s also sometimes a screw that controls the deep of the cut. Other than that, Graphus`s workaround is a pretty common solution.

Replace the motor brass:

If you`ve tried everything and your circular saw still won`t cut wood, the issue is most likely due to a damaged engine brass screw. Your circular saw`s motor is held together by a brass screw, and if it`s missing or broken, your circular saw may stop working in the middle of a job.

Miter saws should only be used to cut wood and non-ferrous materials. It should not be used to cut ferrous materials such as metal bars, rods and studs. The excessive sparking could damage the blade guards and the excessive loading could damage the motor.

For woodworking, a disadvantage of a mitre joint is its weakness, but it can be strengthened with a spline (a thin wafer of wood inserted into a slot, usually arranged with the long grain of the spline across the short grain of the frame timber).

A mitered corner is one of the weaker joints in woodworking because it relies on gluing end grain to end grain. But there are good reasons to make a mitered corner. For one thing, it hides unsightly end grain.

Replace the motor brass:

A broken saw blade, failed drive belt or damaged rubber tire can prevent the blade from moving when the motor runs. Check the condition of the blade and replace the blade if it`s broken.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Trigger switch on my Marksman mitre saw has shorted out and am unable to read part number.No success in contacting Marksman direct.
Machine number 66072c 255mm 1800w 4600rpm PA6-GF30.
5 connection switch.
Any information on locating a replacement would be appreciated

ANSWER :

Read Full Q/A … : Garden

Saw just stop working doesn’t come on check switch looks good. have move then one saw and 2 have just stop running after a while of cutting. Neither where over heated. I have 3 saws 16″ 14″ and pole is the switch the same in all three brfore I take the working one apart. Help.

ANSWER : Did you try them directly in the outlet or with a different extension cord? Have you checked the outlet for the correct power? Did you try a different outlet? Provide model numbers for the bad saws and I will provide an IPL with switch part numbers. Reply below.
Lou
Are you aware RemingtonPower is no longer in production?

Read Full Q/A … : Garden

Have a remington electric pole saw with a short inside the pole,is this fixable and where can I get it fixed?

ANSWER :

Read Full Q/A … : Garden

I have Remington REM55PV heater. It starts just fine but when I take finger off ignition button, heater won’t stay running.

ANSWER :

Read Full Q/A … : Garden

I am in the need of the attachmnent for the

ANSWER :

Read Full Q/A … : Garden

Where do I buy Pole saw parts – Remington Electric Pole Saw

ANSWER : Call 1-800-654-8534

Read Full Q/A … : Garden

Cannot locate parts dealer for electric Remington Limb n Trim 10 chain saw. I require pan head shoulder screw . I live in Alberta, Canada (Devon town near Edmonton)

ANSWER : Here’s a good place to look!http://www.desaparts.com/index.htm

Read Full Q/A … : Garden

Stihl MS250C Chainsaw works great won’t turn off!

ANSWER : That wire should go to the kill switch. IT just grounds out the magento. See the on off switch, and put it back on there.

Read Full Q/A … : Garden