28901 Riding Lawn Tractor

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Failure of any mechanical component, a broken hose, or clogged filter will cause tractor hydrostatic transmission problems. But the most common issue will be the oil itself. In the transmission section of your operator`s manual, you`ll find a section that covers oil viscosity.
If the PTO clutch is not receiving power, the clutch solenoid is defective, or the clutch itself is worn out, the blades will not engage. Since a PTO clutch is not repairable, you will need to replace a broken or worn out clutch with a new one.
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
The reasons why mower is not moving forward or reverse is that the battery is dead, or due to clogged fuel line. Additionally, malfunctioning transmission, or a broken drive belt, also a faulty spark plug, even when friction wheel isn`t in contact with the friction plate, or damaged Tires.
Over time, dirt, debris and other tiny particles can accumulate in the transmission fluid, affecting its fluid properties. This can cause the vehicle to die when you shift into drive or reverse, allow a loss of power, transmission slip, rough shifts or even prevent the vehicle from shifting into gear at all.
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
Grinding gears, starting and stopping during operation, and the wheels not rotating with the pulley are common signs that your mower`s transmission is breaking down.
These control rods are adjustable. By rotating the threaded linkage connector ferrules, the length and the resulting range of movement at the regulator valve can be altered.
Press the Clutch Pedal Down More

If you have a manual transmission, try to press the clutch pedal all the way down to the floor before trying to change gears. As the friction disc down, you have to press the pedal further and further down to move it away from the flywheel.

One of the disadvantages of hydrostatic drives is that the majority of the oil stays in the loop and doesn`t return to the reservoir for cooling. One way to return some of the oil back to the tank is by using a hot oil shuttle valve.
Recommended for all hydrostatic drive systems where the manufacturer recommends SAE 20W-50 fluid.
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it. Need help finding your model number? The PTO switch provides power to the PTO clutch.
They are filled with the specified pump fluid to match each pump design and then sealed by each manufacturer at their factories. Replacing hydrostatic fluid is normally not necessary, unless the drive system is in need of some other internal service or repair.
They are filled with the specified pump fluid to match each pump design and then sealed by each manufacturer at their factories. Replacing hydrostatic fluid is normally not necessary, unless the drive system is in need of some other internal service or repair.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do i install a mulching plug on my craftsman lawn tractor?
ANSWER : It covers the hole on the deck

Read Full Q/A … : 28901 Riding Lawn Tractor

I have a Crafstman Riding mower model #917.273643. That ran fine one second, I shut it off for five minutes. When I went to start it back up it wouldn’t start. Cranks fine, checked the wires, fuse, and spark plug. The plug was dirty so I cleaned it. But I am not getting any spark. I bought a new plug still no spark. I also checked the plug on another motor and I had spark so the plug wasn’t bad. Any suggestions on how to troubleshoot this or what may be wrong?
ANSWER : Sounds like your coil went bad

Read Full Q/A … : 28901 Riding Lawn Tractor

What type of oil for 17.5 42 500 cc – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : I use straight 30wt.

Read Full Q/A … : 28901 Riding Lawn Tractor

2000 white lawn tractor battery runs dead when mower deck is running
ANSWER : Has to be your stater or magneto going bad or had rust on it…

Read Full Q/A … : 28901 Riding Lawn Tractor

I have problem with pulles an my craftsman 17 hp 42in
ANSWER : YOU MUST USE SEARS BELTS ! THERE A ODD SIZE

Read Full Q/A … : 28901 Riding Lawn Tractor

Mower runs for about 5 min, than dies won’t restart . When cool start up ( craftsman 42 in deck 19.5 hp lawn tractor )
ANSWER : Check for spark when it dies you could have a bad coil

Read Full Q/A … : 28901 Riding Lawn Tractor

Craftsman riding mower lt-1000 leaks gas – Craftsman 17.5 hp 42 in. Deck Lawn Tractor – CA Model
ANSWER : Need to fix that. it may be a fire hazard.

Read Full Q/A … : 28901 Riding Lawn Tractor

How do i add transmission oil – Ariens Lawn Tractor 46"" Riding Lawn Mower 936053"
ANSWER : Should a plug or cap on top of transaxle.

Read Full Q/A … : 28901 Riding Lawn Tractor