Garden
My zero turn let me sit in middle of mowing, zero engine runs fine , wont go forward or reverse , any idea wats up
Experienced gardeners share their insights in answering this question :
Zero turn has 2 hydrostatic transmissions. Check drive belt, pulley tensioners for clog.
Remove clog with stick instead of your fingers if in the way of mechanism, belt or pulley wheels.
Check to be sure belt is taught and pulleys move. wd-40 is ok .
Do not get wd-40 onto pulley guides, or pulleys but only to tensioner mechanism and springs.
Paper towels are good spray blockers, wrap belt in paper towels if wd-40, do not use white lithium spray but only small amounts of grease when perform full breakdown and assembly maintenance on deck and drive.
The hydrostatic pumps might be drain&fill possible if they each have a vent hole and a drain plug next to vent hole somewhere. Clean them up with carb cleaner or use starter fluid if really nasty build up. Then check for hex tool drain plug and vent hole or vent cap over hole. Do not use vent hole for topping off hydro’s
Remove clog with stick instead of your fingers if in the way of mechanism, belt or pulley wheels.
Check to be sure belt is taught and pulleys move. wd-40 is ok .
Do not get wd-40 onto pulley guides, or pulleys but only to tensioner mechanism and springs.
Paper towels are good spray blockers, wrap belt in paper towels if wd-40, do not use white lithium spray but only small amounts of grease when perform full breakdown and assembly maintenance on deck and drive.
The hydrostatic pumps might be drain&fill possible if they each have a vent hole and a drain plug next to vent hole somewhere. Clean them up with carb cleaner or use starter fluid if really nasty build up. Then check for hex tool drain plug and vent hole or vent cap over hole. Do not use vent hole for topping off hydro’s
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The reasons why mower is not moving forward or reverse is that the battery is dead, or due to clogged fuel line. Additionally, malfunctioning transmission, or a broken drive belt, also a faulty spark plug, even when friction wheel isn`t in contact with the friction plate, or damaged Tires.
Low tire air pressure on the slow side. A worn drive belt that is too loose on the trans. farthest from the tensioner.
If your lawn mower turns on but won`t move, there could be a number of potential causes. The most common issues include a broken or damaged belt, a clogged discharge chute, a broken or damaged drive cable, or a damaged or clogged transmission.
Your zero turn mower is weak on one side because of one or more of many reasons: traction adjustment being wrong, dragging drum brake, bad dampers, incorrect balance, tire compression does not match, or there is air trapped in the hydrostatic motor.
Failure of any mechanical component, a broken hose, or clogged filter will cause tractor hydrostatic transmission problems. But the most common issue will be the oil itself. In the transmission section of your operator`s manual, you`ll find a section that covers oil viscosity.
Grinding gears, starting and stopping during operation, and the wheels not rotating with the pulley are common signs that your mower`s transmission is breaking down.
Zero-turn mowers use transaxle transmission.
One of the disadvantages of hydrostatic drives is that the majority of the oil stays in the loop and doesn`t return to the reservoir for cooling. One way to return some of the oil back to the tank is by using a hot oil shuttle valve.
They are filled with the specified pump fluid to match each pump design and then sealed by each manufacturer at their factories. Replacing hydrostatic fluid is normally not necessary, unless the drive system is in need of some other internal service or repair.
Check the drive belt that is located just above the mower deck. Follow the belt as it wraps around the deck and to pulleys under the engine and the rear tires. Make sure the belt is secured to the pulleys, because if it is not, then the belt (and thus the mower) will not move. If the belt looks broken, replace it.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Toro cutting off
ANSWER : Maybe low oil level, all mowers have a low oil cutoff. 30w oil.
Read Full Q/A … : Garden
Diagnosing possible pto issue – Toro Zero Turn Rider 74366 Lawn Mower Tractor Rider Ztr
ANSWER : Check plug on the pto itself.located under the mower near the rear end. contacts probably have dried dirt and mud. if that don’t work, tap it with a hammer,it may be just stuck.Thats what I did and it been working ever since. Hope this helps someone.Let me know.
Read Full Q/A … : Garden
Battery goes dead over night – Toro 42'' Zero Turn Lawn Mower Trailer Package Deal ()
ANSWER : First thing to do is find out if it’s the battery or the mower. Disconnect the battery and leave it overnight. If it’s dead in the morning, you need a new battery. If not, you either have a charging problem (not likely if the battery isn’t dead after using the mower) or you have a current drain.
Read Full Q/A … : Garden
<!– from fixya rte –>How do I engage bagger on zero clearance – kawasaki 48'' Toro Com Zero Turn Lawn Mower 21hp Kawasaki ()
ANSWER : That should be covered in your manual. I’m not sure what a zero clearance mower is actually, are you assuming and making up a name for it?
Read Full Q/A … : Garden
Why wont my blade engage
ANSWER : Bad pto clutch shorting out
Read Full Q/A … : Garden
Engine runs, blades turn but mower will not move
ANSWER : Look in front of back tired on frame, not deck, there are. 2 rods, 1 on each side, rods look like a L, it’s going through a little eye opening, push it backards, mower should move. If rod is pulled through opening and locked in, mower will not move..its a safety. Feather on mower
Read Full Q/A … : Garden
19 h.p. kawa mowing and motor stopped. Will not turn over at all. PTO was engage when shut down
ANSWER : See if it vapor locked pull plugs out and turn it over without them in if works put plugs back go on down the road and mow
Read Full Q/A … : Garden
Blowing oil out of the engine – Toro 52" 27hp Z Master Zero Turn Lawn Mower
ANSWER : Check oil level fuel could have flooded through into the engine oil which will cause it to blow out if so clean out carby and check that needle in the carby is sealing
Read Full Q/A … : Garden
