Briggs Stratton Lawnmower Lawn Mower Short Block
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Why Is Your Lawn Mower Pull Cord Hard To Pull? Your lawn mower pull cord hard to pull is because of the way you pull the cord, the area where your mower is located when you are trying to start it, because it has a blade obstruction, or because of a starter mechanism-related issue.
A Briggs and Stratton lawn mower engine can become locked up due to a variety of reasons. Common causes of this type of engine lock-up include a lack of oil in the engine, incorrect fuel and spark plug misfiring.
Pour penetrating oil into the cable (Photo 1). Grab the inner cable with pliers and work it up and down to loosen it. When the cable moves freely and all the penetrating oil has drained out, squirt silicone lubricant into the funnel to keep the cable sliding freely. Reinstall the cable (Photo 2).
An engine can seize due to running on low/no oil, overheating or succumbing to a broken timing belt. These conditions eventually stop your engine in its tracks and a professional technician will be required to restore function.
To make pulling the cord easier, shift the lawnmower height up to start the machine, then lower it back down to your desired grass height to begin cutting.
When the rope`s grip is pulled, the rope uncoils, tensions the spring, engages the clutch and turns the crankshaft, spinning it to crank or start the engine before the end of the pull stroke. The running of the engine then disengages the clutch.
Sometimes, when your starter rope will not retract into your leaf blower, it can be because it is jammed between the pulley and the housing, or it is wrapped around the hub. In this case, you will often be able to fix the symptom by simply opening the machine and untangling or removing the rope from where it is stuck.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
No response to clarification request.
Troy Bilt Lawn Mower pull Cord broken
There should be four bolts holding the cover on that houses the pull cord assembly take the bolts out look inside you should see the rest of the broken cord at the other end there is a spool that the cord rolls up in to pull the cord until it stops the other end of the cord is a not in the cord pull on the knot the broken peice should come out turn the spool 2 times in the direction that is against the pressre while holding the spool in place feed the new cord in through the whole that you pulled the broken cord out of then tie the cord in a knot wind the rest of the cord up then feed the other end of the cord through the new pull handle tie the cord in a knot put the housing back on
Weed eater is locked up. can not pull cord at all.
Try taking the cover off around the pull if you can. Likely the cord is not free to spin, or there is a rub on the fly wheel stopping it from moving.
Starter cord pulled out of the housing, it
If it’s new take it back should have a one year warrenty on it if yo can’t get it done for free get back to me so I can help you you may have a damaged windind head.
My chainsaw starts when there is no bar and chain on it but when I put the bar chain and side casing back on tighten the chain and pull the starter cord it is hard to pull and then the chain goes loose again
Have you just replaced the chain?If so there is a possibility the chain and drive sprocket don’t match causing the engaging spurs to ride on the sprocket teeth
The pull cord will not recoil. what do i do? the spring behind the cord was just assembled and went to pull it and it wont recoil the pull cord.
It needs a pre-tension. At about 1 minute and 22 seconds it is explained clearly here:
The pull cord on my ZR29550 string trimmer is stuck in the fully retracted position. I can’t pull it to start the machine. Also the electric starter can’t turn it over.
Well its not going to start with electric because the cord is out of it…
just take it apart becareful do not pull the recoil out or your in a mess….
but this should help you out if you need to know more just ask…
What to do when craftsman mower pull cord won’t recoil?
Sounds like the spring inside the recoil has either broken or let go so it won’t recoil. If you are lucky it could be the wheel that the cord goes on is seized or stuck. You can take the recoil off most mowers by taking out two or three screws and lifting it off the engine. They can be repaired but it takes time having to be careful the spring won’t spin and hurt you. I have even taken a recoil off another engine and if the holes for the little screws don’t line up just drill little holes beside the old ones and reinstall the little screws.
I even used a 18 volt cordless drill to crank the engine using the bolt on the fly wheel and the right size socket. Leaving the recoil off You have an electric start that way.