25cc Gas Line Trimmer

Troy-Bilt model tb525cs gas trimmer. Has been working fine recently.
I took it out to work and the starter pull line will not pull enough to start it.
Experienced gardeners share their insights in answering this question :
Remove spark plug to see if problem is in engine or drive unit

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If the pawls do not retract then the springs need to be replaced. Remove the center bolt and cap, remove ratchet pulls, use pliers to pull out the old springs, then install the new springs and re-install the pawls. Reinstall the center bolt and cap and the starter back onto the engine.
Sometimes, when your starter rope will not retract into your leaf blower, it can be because it is jammed between the pulley and the housing, or it is wrapped around the hub. In this case, you will often be able to fix the symptom by simply opening the machine and untangling or removing the rope from where it is stuck.
When your trimmer starts and runs on choke, it could be because the check valve in the gas cap is clogged. Start the trimmer and gently unscrew the gas cap halfway off. Turn the choke off and assess. If the engine is still running, that means the gas cap may be the culprit.
A clogged carburetor is most commonly caused by leaving fuel in the string trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall.
Converters are unlocked from the Coins shop by purchasing Unlock Converters for 200 coins.
Unfortunately, you also know the struggles that come with it. Your bathroom pull cord keeps breaking for 1 of 3 reasons. Either it`s had too much heavy-handed use, it was cheaply made, or you`ve got a loose wire somewhere. Whichever one it is, there`s a solution for you.
What is the Difference? Lawn edgers are designed to cut edges and create boundary lines, whereas a string trimmer is designed to maintain those boundary lines. They make a great team! Both can help your lawn to look sharper.
What is it? The Automatic Feed Spool (AFS™) is the technologically advanced line feed system found on Black & Decker string trimmer products such as the Grass Hog™, Trimmer/Edger, and the 12″ Cordless Trimmer/Edger.
The problem may be in the recoil starter itself. A tangled coil of rope or a broken spring may be the problem. In many cases the recoil starter is easily replaced as a single assembly. DO NOT attempt do take the starter apart.
To make pulling the cord easier, shift the lawnmower height up to start the machine, then lower it back down to your desired grass height to begin cutting.
Raises alerts in areas where personal triggers are unlikely to be worn. The emergency Pull Cord can be strategically placed around the home, in order to provide a user with a convenient means of summoning help in an emergency.
Pull the plastic housing of the electric plug to take it out of the wall socket; never pull on the cord. Do not overload electric outlets with too many items plugged in at once.
The clutch engages the clutch pads to spin the trimmer head. If the clutch assembly is defective, the clutch will not disengage the clutch pads, and the trimmer head will continue to spin, even at low speeds. If the clutch is defective, replace it.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My edger tipped over briefly, now the starter cord is hard to pull and it won’t start.
ANSWER : Try removing the spark
plug and squirting some carb cleaner or starting fluid in the
cylinder. Pull the starter cord several times for the piston to drive
out the oil. Clean the plug and replace it. Try to start as normal.
If you have starting fluid squirt a shot in the air cleaner to help
make it easier to start the first time.

Read Full Q/A … : 25cc Gas Line Trimmer

I need to replace to fuel lines on a Craftman 32cc trimmer. The old ones cracked apart. 2 of the lines look like 1/8″ OD one line looks like 3/32″ OD. Larger line looks like it hooks to filter, Smaller line to a fitting in the gas tank. I am assuming the smaller line ges to the primer inlet. My question is the lines penetrate the bottom of the gas tank. How do they seal. How do I install the filter and the fitting. I am assuming to thread the new lines in from the bottom of the tank and pull through the gas cap hole. Then I attach filter or fitting and pull back through. So do I pull the line so as to create a seal from the swell caused by the fitting/filter?
ANSWER : Depending on the brand of line you use, Tygon line is self sealing but seems to shrink faster then factory supplied because of the ethanol in the gas. The stone gas filter is designed to fall to the lowest part of the tank, not stop the line from falling out.

Read Full Q/A … : 25cc Gas Line Trimmer

I cannot get the line to feed as it is used up. bumping does no good. the spring is in place. thanks for your help
ANSWER : Did you wind in the new string in the correct direction? The string should be wound in the SAME direction that the head spins.

Read Full Q/A … : 25cc Gas Line Trimmer

Can not get spool head apart to change line, tried pump pliers, pipe wrench, won’t unscrew!!
ANSWER : If you are sure that it screws on it may be a reverse threaded unit..

Read Full Q/A … : 25cc Gas Line Trimmer

Auto feed doesn’t work
ANSWER : Take the end apart and make sure the line is not getting bound up or is not over filled to where it can not move freely

Read Full Q/A … : 25cc Gas Line Trimmer

Need to know how to wind trimmer line on trimmer
ANSWER : Depends on the trimmer, all heads are different. However, the majority of trimmers are wound as follows:

1. pop the top cover off the head, pull the spool out. It will be either single or double lined, they will be wound counter clock wise.
2. the end of each line goes out each of the seperate holes
3. slide spool back on and replace cover

www.ButlerPower.com

Read Full Q/A … : 25cc Gas Line Trimmer

How do i replace pull cord on my craftsman gas line trimmer model 358.796600. i can’t fugure out how to replace pull cord . i can’t get to pull cord housing
ANSWER :

Read Full Q/A … : 25cc Gas Line Trimmer

Trimmer head line loading instruction – Husqvarna 28cc Gas Line Trimmer
ANSWER : 1. Remove the cap on the trimmer head, it unscrews.2.
The spool comes off, and on the inside of the spool there is a small
hole, this is where you will start your trimmer line. It it will hold it
in place while you wrap it. There is also arrows on the spool showing
the direction that you need to wrap your spool.3. Insert the
line in the hole and start to wrap the line in the directions of the
arrows, try to keep the line in rows, or else the line may bind and you
will have to do it all over again.4. Feed the line through the
retainer and reinstall the spool by lining up the retainer and the slot
on the outside portion on the trimmer head, the screw back on the
trimmer head and you will be ready to trim.

Read Full Q/A … : 25cc Gas Line Trimmer