Riding Lawn Mower Yth24v48ls 48 Inch Cut

Experienced gardeners share their insights in answering this question :
Husqvarna uses an electronic clutch to engage the mower deck. When the clutch works itself out of adjustment it will quit working. Sometimes it will blow the 20 fuse and the tractor will continue to run, but the blade won’t engage. When you then shut off the tractor it won’t crank again until you replace the fuse. When you attempt to engage the blades again, the fuse will blow again.

Follow this link for a detailed description of the adjustment process:

http://www.lawnsite.com/showthread.php?t=164509&highlight=clutch+adjustment

Nick

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your Husqvarna riding mower blades don`t engage, you need to check the PTO switch, drive belts, frozen pulley, and make sure the battery is charged. Moreover, you can also check to see if the blade clutch is working correctly and the safety switch is off.
The reasons why mower is not moving forward or reverse is that the battery is dead, or due to clogged fuel line. Additionally, malfunctioning transmission, or a broken drive belt, also a faulty spark plug, even when friction wheel isn`t in contact with the friction plate, or damaged Tires.
Worn or broken blade drive belt – If the riding mower blades are not spinning, the blade drive belt may be worn or broken and unable to engage the blades. If the belt is intact, inspect it to see if it`s loose or slipping on the pulleys then replace it with a new one if necessary.
There is a safety switch at the end of the cutter engage lever which has gone faulty and needs replacing, overiding the switch by keeping it pressed in will allow the mower to be operational till replacement switch is fitted.
Your Mower Won`t Start:

Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.

If the riding lawn mower runs but the blades won`t cut the grass, the problem could be with the blade belt. Examine and replace the belt if you find it worn or broken. If the belt is okay, check the blade belt idler pulley, blade clutch cable and clutch lever assembly on tractors with manual blade actuators.
Identify if Your Lawn Mower Blades Need To Be Balanced

So to ensure that your lawn mower blades need balancing, look for unbalanced lawn mower blade symptoms like your lawn mower is not giving your grass a quality and even cut, as well as vibrating and making odd noises while running.

If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
A low charge may not provide enough juice to engage the PTO. If you do hear the click, there is power going to it. There could be a problem with safety switches. On most newer model lawn mowers, the brake has to be disengaged or off for the blades to operate.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Mower won’t start
ANSWER : This may sound stupid but don’t mean it to…
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.

Hope it helps.

Anthony

Toro 149cc Lawn Mower Won't Start – Toro Lawn Mower With Toro Power Tools
ANSWER : Bad carburetor your old fuel jammed up the jet so it won’t get fuel and if it does it will start and shut off So replace the carb or try to clean the jet and run non oxy fuel only

Have a john deere sabre turn key won’t start thought battery was dead charged battery still won’t start jump start with car battery it will start then . try to engage reverse with blades running it shuts off. shut down tractor won’t start again .I,m thinking wiring not grounded but where or replacement switch somewhere.give best advise.
ANSWER : Some mowers have a mowing reverse safety switch. That safety will kill the mower if you try to reverse with the deck engaged. Some mowers even have an override button that has to be held while backing up. As for the battery thing, no matter how much you charge a bad battery you will not get it to start a mower if it has a bad cell or two. I would use a multimeter to check battery voltage, but the end result would still be the same, replace the battery.I hope this gets you going again.

Mower won’t start. Toro mower..engine won’t turn over. Cleaned sparkplug…checked air filter..weather cool. Followed instructions for cold engine…prime witrh three pushes of the bulb..wnon’t even hint at a start..
ANSWER : Something everyone over looks is oil. Did you check the oil? You seemed to mention everything else but. If you have a low oil switch with low oil it will not start

My toro 6.5 hp push mower (2010), has no fire to the plug. I have not abused it. i have a small yard and it just gets normal use. Now it won’t fire. I first changed the fuel and cleaned the carb thinking it was that crappy ethanol again. but i grounded out the spark plug and cranked it…no spark. I think it has to do with the lever you pull back to start it . they have some stupid complicated safety contraption that rides along the fly wheel when you pull back on the handle for starting and shutting off the engine. …it looks worn out already…like a mini brake pad. any ideas?…do i really have to replace this garbage every year or am i on the wrong path here?
ANSWER : Unhook your wire from the coil that goes to shut off mechanism, and see if you have spark then. the wire may be grounded out, or your coil might have took a ****

B&S Quantum Power 4hp won’t start with fresh plug,
ANSWER : Did it run before you changed the plug?Gap is correct, flywheel shear pin may be bad, Water in the Gas?

My mower will start but won't stay running – Toro LX466 22HP Lawn Tractor 13RT61RH244
ANSWER : I am going to respond 2 times to this post. The first reply will be generic things to check.
First off check the oil level and make sure it is serviced to full.
If your having a lack of fuel (runing lean) you will need to check fuel flow at the carb fuel mainfold. It should fill a spray paint can lid in less than 10 seconds but teting flow rated of the main fuel line. If you have poor flow here… you need to check the fuel filter and the fuel tank outlet port for obstructions.

Good Fuel flow still shutting off…. remove the carb float bow and clean the debris from the bow’ and the treaded area where the fuel solenoid mounts Additionally you will have to again remove the main fuel line and spray carb cleaner in the float needle area to flush out any debris through the fuel hose connection.

For the second response I need to know which engine is installed on your mower by MODEL number if you can locate it. (there are 3 engines) At least try to find the engine model number. If you can not locate it Brand and HP of the engine (I assume 22 hp) Thanks for choosing FixYa,
Kelly

I have had a poulan pro 550 series push mower for almost 1 year at the end of the season last year the mower would start briefly and then stop. i have cleaned out the air filter and that did not help.the mower started, i made one revolution around the yard 3/4th of the way the mower quit. I then primed the mower it started then quit and now it will not start at all. Does anyone have any suggestions of what to do. Thanks
ANSWER : There is a little spring that works the carburetor arm. If that popped off then the mower will not run.