the carberator and one to the engine. The one from the engine is blowing a gas-fuel mixture back into the air filter, causing the carberator to be smoothered and the air filter to be covered in gas/oil. How do I fix this?
Briggs & Stratton

Experienced gardeners share their insights in answering this question :
You have a leaking fuel valve in the carburetor bowl.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A Dirty Carburetor Can Cause a Lawnmower To Start Then Die

By far, the most common issue that causes a stalled motor is a dirty carburetor. The carburetor on your engine is the thing that draws in air and mixes it with the fuel. Contrary to what the movies might make you think, gasoline itself is not very flammable.

Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas. If this doesn`t work, you might need a new fuel filter.
If your lawn mower starts, runs briefly, then dies these are the four most common reasons that`s happening: Dirty carburetor / clogged carburetor bowl. Old gasoline that has gone bad. Dirty or defective spark plugs.
If your lawn mower starts, runs for a while, then dies, check the ignition coil, gas cap, and spark plug. One or more of these parts could be causing your problem. Follow our repair and symptom guide to help you fix this.
Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas. If this doesn`t work, you might need a new fuel filter.
Use Carburetor Cleaner

Fortunately, you can generally do this without even taking the carburetor out of the engine. Start by purchasing some commercial lawnmower carburetor cleanerOpens a new window, which comes in a simple spray can and will make it easy to clean the inside and outside of the carb.

Over time, a spark plug will wear out. Eventually, the spark will no longer be powerful enough to fully ignite the air and fuel. You are likely to notice power loss including bogging down when cutting grass because of a worn spark plug. Removing and replacing a spark plug is easy.
An airlock is one of the common causes why your mower won`t start after running out of fuel. An Airlock occurs when air replaces fuel in the fuel lines. As you refill your fuel tank, you could push the air towards your mower`s carburetor, which keeps the new fuel from reaching the engine.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Chainsaw stalls Chainsaw is 4 years old and has a history of moderate use. After I ran the saw about 1 minute on plain gas (grabbed the wrong gas can – ouch) the chainsaw sputtered and stopped.

It didn't seize, and the pull starter never became more or less difficult than normal. The engine would continue to start if I pressed the prime bulb and engaging the choke, but stall again after 10-20 seconds. The temperature that day was about 50 degrees F and I was running the saw with the “cold plug” installed (per warm weather running).

When it refused to keep running I did the following:
Flushed the fuel tank (that's when I saw the gas had no oil in it).
Ran hardware wire through all of the fuel lines.
Replaced the fuel filter and spark plug.
Cleaned the air filter with a nylon brush and compressed air.

Same behavior (start then stall in less than 20 seconds). I made at least 20+ attempts to start it.

I removed the carburetor and, though it looked perfectly clean, I took off the top and bottom covers then sprayed everything with automotive carb cleaner and blew out the passages with compressed air. The gasket and diaphragm looked new. No pinholes in the diaphragm when held against a bright light. I reinstalled the carb but got the same behavior (start then stall in less than 20 seconds). I again made at least 20+ attempts to start it.

I disassembled the short block and saw that the piston has some slight scoring on it. The ring is clean and I verified that the piston ring has .001 clearance between it and the piston ring groove all the way around with the ring held tightly in place (I was thinking that the piston might have become deformed if it did indeed get too hot when run without any oil premix).

The cylinder wall has no scoring and there isn't any signs of melted aluminum anywhere. The crank is clean as was the inside of the crank cover.

I reinstalled the crank cover using permatex non-hardening gasket goop and torqued the cover bolts to 10 inch pounds. I reassembled everything else per the exploded diagrams in Echo's “parts manual” for the CS400.

During assembly I took note that both the carb gasket and intake boot look like new.

Still the same result: press prime bulb once, engage choke, pull a few times and it starts but stalls after 10-20 seconds.

I'm stumped.

ANSWER : Not sure what to say other than its fuel starvation, if not already done replace the fuel filter in the tank, if no better i would suspect a massive air leak, so replace the crank seals, if there is no primary compression in the crankcsae fuel will not pull through the engine, good luck.

Read Full Q/A … : Briggs & Stratton

Wont start no ignition put new plug in and fuel filter
ANSWER : Flush gas tank, fill with fresh gas and Stabil. Replace air filter. Remove bowl from carb clean bowl and holes in bowl screw.

Read Full Q/A … : Briggs & Stratton

My tractor stalls like it is starved for gas although the gas tank is full. I,ve changed the fuel filter and the gas cap. I’ve cleaned out the gas tank, gas lines, and the carburetor bowl. The problem seems more acute when the gas tank is full or near full. At this time to alleviate the problem, I blow through the gas cap and the fuel filter fills with gas and it runs good again. But as soon as the fuel filter has no more gas, of course, it stalls until I blow on the gas cap. As the tank gets down to about 1/3 full, the engine runs OK. What else could cause this condition?
ANSWER : I had a similar problem with a sears tractor. close to the carbarator is a rectangle box with a rubber hose going to the engine block – remove the hose and spray carb cleaner in the hose wait a few mins and try again – its a vacuum for the carb

Read Full Q/A … : Briggs & Stratton

Petrol is spewing up from air filter on briggs and stratton 90208 ride on mower
ANSWER : Lol too much oil bud take a little out

Read Full Q/A … : Briggs & Stratton

Gas to oil mixture for a RY 26540 – Ryobi 30 Cubic Centimeter Curved Shaft Gas Trimmer
ANSWER : 50:1 don’t use outboard motor mix

Read Full Q/A … : Briggs & Stratton

Will not start turns over has spark the engine was running and killed and will not restart
ANSWER : If you have good fuel to the plug and a good spark and it still does not start it could be a timing issue, check the flywheel key has not sheared.

Read Full Q/A … : Briggs & Stratton

The mower starts and then stalls out. I changed the air filter, fuel filter and spark plug. The air filter has two tubes coming from it, one to the carberator and one to the engine. The one from the engine is blowing a gas-fuel mixture back into the air filter, causing the carberator to be smoothered and the air filter to be covered in gas/oil. How do I fix this?
ANSWER : You have a leaking fuel valve in the carburetor bowl.

Read Full Q/A … : Briggs & Stratton

Fuel,gas oil mixture – Echo 30.1CC Chainsaw With a 14 In.bar and Chain
ANSWER : The fuel/oil should be in the ratio 50 to 1

Read Full Q/A … : Briggs & Stratton