Garden
Experienced gardeners share their insights in answering this question :
It depends on what brand. Usually they are held on by plastic tabs that go into a slot on opposite sides of the head.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
Hold the weed whacker with 1 hand on the trigger and the other on the handle. This is both the most comfortable and safest way to hold your weed whacker while you`re using it. Be sure to keep the trigger end at waist level at all times.
A trimmer comb is a simple attachment that can be mounted on top of the trimmer blades to create a gap between the blades and the skin, so that you can control the length of the beard on your face. It`s made with smooth edged plastic, which makes gliding them along or against your beard smooth & easy.
Not all strimmer heads are the same size, and there`s a lot of variety on the market. Blade heads that describe themselves as `universal` are generally compatible with the majority of strimmers; however, there are some important factors to bear in mind.
Here`s the deal, some lawn care pros have found that they can simply see the string better when they edge without a guard on. This allows them to better control the cut the trimmer is making as they walk along the edge they are clearing. Which can allow you to make a straighter cut and a sharper edge.
It is wise to always hang a string trimmer in a vertical position instead of storing it in a horizontal position. Not only does vertically store this tool saves a lot of wasted space, but it also keeps the delicate engine components from getting damaged.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
How do you take off the spool head of a craftman weedeater and replace it with a precut line head?
ANSWER : You can remove the spool by pulling firmly on the tapper button to remove it. The spool will then be exposed and can be replaced. reinstall the button by snapping back into place.
Read Full Q/A … : Garden
Removing spool on weedeater SG11 Electic
ANSWER : Pull on the tap head. Straight out. Hard. Here’s the Weedeater manual. http://72.3.225.179/manuals/545117522e.pdf
The spool should just pull out, its held in by 2 clips, royate it till it pops up then pull it out, with a wiggling motion,
Grasp firmly and pull straight out….per tech support from 800 number on machine.
Read Full Q/A … : Garden
How do i adjust the carburetor high and low mix on a weedeaterblower fb25..
ANSWER : Initial start adjustment is 1 full turn out on both low and high side.
Read Full Q/A … : Garden
How do you know whether to use 50:1 or 40:1 gas/oil ratio mix in a 2 cycle engine ?
ANSWER : Should be written in the manual and on the lid if not i always run 40 to 1 better safe than sorry to much oil ratio can foul a plug running to light on oil can blow the motor
Read Full Q/A … : Garden
How do i replace a spool on the weedeater xt110. I cannot seem to get the spool to release and I do not have the owner’s manual.
ANSWER : Just line up the two arrows across from each other to those on the the spool housing on the bottom of the spool. Then grip the bump knob and pull straight out. It takes a good grip and some force, but it usually gives way.
Read Full Q/A … : Garden
The head keeps falling off my weedeater brand weed eater
ANSWER : Add a split washer. Turn it tight enough to compress the split into a flat washer. The spring tension of the washer will hold it on. If not, you will need to add some Loctite.
Read Full Q/A … : Garden
Where can I buy a replacement head (or whole new shaft) for my M-Line weedeater?
ANSWER : Try sears aka crafsman .
Read Full Q/A … : Garden
What should the spark plug gap be on a weedeater trimmer 25cc
ANSWER : Set it at .025
Read Full Q/A … : Garden
