Honda

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The recommended pressure is: Front 170kPa (24 P.S.I.). Rear 140kPa (20 P.S.I.) This machine is fitted with a maintenance free battery. Before operation ensure that engine oil level is to the full mark on the dipstick.
All tractor tyres should be checked for proper inflation pressure, the factory settings are generally 10 psi. for rear tyres, and 14 psi. for the front.
Packed with features including our legendary COX Proprietary front scallop deck entry, both models are powered with COX 26hp VTwin engines and Hydro-Gear ZT2800 servicable transmissions.
In short, we recommend beginner trail riders start with the following pressures on tubeless tyres: Front: 27 PSI. Rear: 30 PSI.
SECURITY Tyre 155/80R13 84N, TL, AW-418, M+S, suitable for all common trailer types. build design radial, tyre size 155/80 R 13, TL (tubeless), load index 84, speed index N, tread AW-414, specification M+S, load capacity 500kg at 140km/h, inflation pressure 2.7 bar.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Wont start no ignition put new plug in and fuel filter
ANSWER : Flush gas tank, fill with fresh gas and Stabil. Replace air filter. Remove bowl from carb clean bowl and holes in bowl screw.

Read Full Q/A … : Honda

Mower start up and runs, but starts to cut back, and smokes just a little bit. The mower stops smoking when it throttle up. It will continue to run but not at full throttle. I can hold a finger gently over the fuel primer bulb and it will throttle up for a small time.
ANSWER : It sounds like she’s being deprived of the correct fuel / air mixture due to a dirty carburetor (the biggest problem with mowers when gas is left to sit for a period of time). If you do not know how to take the carburetor apart and clean it thoroughly, then I suggest taking it to the local shop (hardware store or mower shop) and having it tuned up. It’ll probably be just fine and worth the money. Hope this helps and good luck.James

Read Full Q/A … : Honda

Have honda harmony 11 HR 216 that stopped being self propelled. What should I look for. I don’t even know if this mower is front or rear wheel drive. But I think rear wheel as they are worn more. Does this have a belt? Does it have trans fluid? What do I have to do to check out the problem? I have never worked on a propeled lawn mower.
ANSWER : It has a belt look under the mower

Read Full Q/A … : Honda

Honda HRR216 does not start at all ,what could be the problem
ANSWER : Hi arshadmalik5…

Check to make sure you are getting fire/spark at the plug, if so then do the following:Check/Clean/Replace your fuel filter if you have one.If the mower/weedeater/edger is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.Sounds like you will need to clean the carburetor or replace your carburetor internal rubber parts like the diaphgram and O rings.Be sure to use compressed air to blow out all the fuel and air passages.Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.Sometimes you can get by with priming the carburetor or using starting fluid and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.Keep in mind that the float for the carburetor must be level when you go to reassemble the carburetor or follow the instrucitons you get with the carburetor kit.When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.Be sure to mark the turns down on a piece of paper.That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their orginal position before you started.
This is a FREE answer,Please rate me

Read Full Q/A … : Honda

My Honda 160cc lawn mower engine cut out when I hit a large clump of grass. Now I cannot get it to start. Has always started with no problems. What to do?
ANSWER : Has probably broken flywheel key ….. putting it out of time

Read Full Q/A … : Honda

What type of oil doesa honda gcv60 use?
ANSWER : GCV160 engines take 10W30 oil.

Read Full Q/A … : Honda

How to tight my drivimg belt in my push mower honda
ANSWER : The model shown 11A-034F200 is not a self propel mower. Now if you have a self propel mower, most of the time, the only way is either replace the belt or there may be a spring. I will not be able to tell you further without the proper model number.Good Day.

Read Full Q/A … : Honda

Craftsman mower honda engine, leaves circular marks in lawn, new blade did not help
ANSWER : Try raising the deck up a little.Thanks for asking and I hope this helps out.Please leave me 4 thumbs up.

Read Full Q/A … : Honda