Statuary Water Pumps Pump 1

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Aquascape Statuary Water Pumps can be used as a tabletop fountains, ornamental spitters, and statuary submersible pumps. These energy-efficient, magnetically-driven, oil-free motors prevent water contamination.
There are also three main types to choose from: single-speed, two-speed and variable-speed pumps. Let`s learn more about these pumps and which one is right for your backyard pool.
Once you have the measurement, choose a pump that is at least 1.5 times the head height. So, if a fountain has a head height of 40 inches, you will want to choose a pump that has a maximum lift of at least 60 inches or more to ensure strong water flow in and out of the fountain.
There are two primary types of pool pumps: single speed pool pumps and variable speed pool pumps. Single speed pumps do just that: operate at one – single – speed. Whereas variable speed pool pumps allow a user to adjust the flow rate of the water through the system at, you guessed it – varying speeds.
Select the Right Size Swimming Pool Pump

You might think bigger is better in terms of pump size. However, a pump that is too big can cause serious problems. To get the right size pump, you need to know the volume of water in your pool. The volume is the pool`s total capacity, which is measured in gallons.

Firstly, it`s important to point out that there`s two main categories of water pumps, namely: centrifugal pumps, and. positive displacement pumps.
A water fountain pump is a device that creates a water flow from a water source (like a pond, pool of water, or water barrel) and pushes the water through a hose or piping and into a water feature.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do I “bleed” air from pump ? Motor runs, but it does not pump water.
ANSWER : Check the suction side and see if it is clear to allow water flow.

Read Full Q/A … : Statuary Water Pumps Pump 1

My pool pump makes a buzzing noise but there is no water circulating into the pool and no suction what-soever. What could be the problem?
ANSWER : First, Check your voltage at the terminal with a voltmeter. If it is within 10% of what is stated on the name plate, try the following suggestions. If is is more than 10% off, call an electrician. Common problems that cause this humming with no suction in these pool pumps are:-Take the pump apart and look for rubbing that could be causing your pump to tighten up. -Check for a seized motor. If the motor has seized up, you will have to have it repaired or replaced.-It could be a winding switch or capacitor problem. Again, a pro will have to service it.

Read Full Q/A … : Statuary Water Pumps Pump 1

Why is my sand pump filter not cycling pool water; the intake line along pool wall seems to be clogged.
ANSWER : I had this issue on a hayward. Bottom line, look at the secondary filter on the intake. I had a huge amount of leaves in there. When you open it up clean the basket and let the water flow for a minute. Also, back wash your filter.

Read Full Q/A … : Statuary Water Pumps Pump 1

My pump is no longer working my pool water is starting to turn green, I shut down the power but I can’t seem to open up the pool pump to clean the basket can you give me any suggestions?
ANSWER : First get some liquid chloriene in the pool start with about four gallons. Loosten the lid ring then turn the pump on and back off after a few seconds. If your trying to get the pump housing open do the same thing with the lock ring that holds it closed.

Read Full Q/A … : Statuary Water Pumps Pump 1

How to remove a underground swimming pool pump
ANSWER : If the pump is above water level there is no need for valves. If the pump is below water level, partially drain pool until water level is below pump, then install unions and shut off valves when you remove the pump.

Read Full Q/A … : Statuary Water Pumps Pump 1

I have a 1/2 horse wayne shallow well pump. At times the water in the house slows to a trickel. This will happen for about 40-120 seconds then the pump seems to kick on and the pressure is restored. I have replaced the high low switch and the problem persists. Please let me know any thoughts on the problem. Thank You
ANSWER : Check air in your water tank should be less than you’re cut in pressure..

Read Full Q/A … : Statuary Water Pumps Pump 1

Leakin water pump
ANSWER : The water pump on a car has a bearing that blocks a hole when working. When the pump goes, it pulls the bearing from the hole and leaks. This is very common, and it was made this way for pin-pointing the issue. The water pump should be replaced.

Read Full Q/A … : Statuary Water Pumps Pump 1

I hav a pennacle pump modle part 7_177474_01 – Grundfos MQ3-45 1 HP Pressure Booster Pump
ANSWER : WARNING YOU MUST PRIME THE PUMP FIRST
about 3 gallons. if you don’t it will burn up the shaft seal and slowly
leak water into the motor.. need more help search your area for the pool
pump repair guy and ask him for help you might be able to get the motor rebuilt, cost about $75.. pictures are a big help so have a
few on hand ready to email.. Jay the pump guy in longwood Florida

Read Full Q/A … : Statuary Water Pumps Pump 1