Honda

Experienced gardeners share their insights in answering this question :
Thought it was a free advice web site? Scammin’ scumbags!!!

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

There could be small leaks, holes, or tears in your garden hose or high-pressure hose that are causing your pressure washer to lose pressure when you pull the trigger. If you find leaks, plug the holes or replace the hose, which should solve your pressure issues.
The number one cause of low or no pressure when using a pressure washer is a blocked or worn nozzle. Blocked nozzles will prevent water from escaping, while a worn nozzle will allow too much water to pass through, causing the pressure to drop.
A clogged carburetor is most commonly caused by leaving fuel in the pressure washer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to run stall.
Clogged carburetors or air filters can cause a pressure washer not to start. If your pressure washer won`t start, you can also check for a clogged carburetor or air filter.
Water leaks and inconsistent behavior are also signs of a potential failure in the near future. González: The typical signal when there is an unloader malfunction is a reduction of flow through the nozzle, which results in pressure loss. Dean: Typical symptom of an unloader failure is a sudden smooth pressure loss.
Low Engine Oil Shut off

Many brands, like Honda, have a low-engine oil-shut-off feature. The pressure washer starts normally, runs for a few seconds, and then dies. Solution: Check that your washer has enough oil in it. It is critical to check oil levels before starting your washer.

How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
Problem: The pressure washer is pulsing.

If the machine is pulsing whilst in use, it may be that the accessory you are using has a blockage. Clear by soaking the accessory in warm soapy water and then rinsing out under the tap.

If the spark arrestor is dirty or damaged, it can cause the engine to stall. To clean the spark arrestor, you will need to remove it from the pressure washer and use a wire brush to remove any build-up. Once the spark arrestor is clean, you can reattach it and try starting the power washer again.
How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
The vast majority of pressure washer spray guns feature a trigger lock that can be used when you need to step away from the pressure washer. Utilizing the trigger lock will prevent any unintentional spraying and accidents.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

The engine surges at idle and then does not run constantly underpressure. sounds like fuel but cleaned all lines and used new fuel. any suggestions
ANSWER : A new spark plug and don,t forget to push in the choke after start.

Read Full Q/A … : Honda

Toro 149cc Lawn Mower Won't Start – Toro Lawn Mower With Toro Power Tools
ANSWER : Bad carburetor your old fuel jammed up the jet so it won’t get fuel and if it does it will start and shut off So replace the carb or try to clean the jet and run non oxy fuel only

Read Full Q/A … : Honda

When I start it the engine surges. When I pull the handle on the wand the engine will not go to max rpm.
ANSWER : Check to see if the choke is not on.

Read Full Q/A … : Honda

Toro clear won't start – Toro Power Clear 621 R
ANSWER : Bad gas , plug ,air filter , no spark ck all need all 3 to start

Read Full Q/A … : Honda

Mower won’t start
ANSWER : This may sound stupid but don’t mean it to…
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.

Hope it helps.

Anthony

Read Full Q/A … : Honda

Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works

Read Full Q/A … : Honda

PWER WASHER RUNS PERFECT, WHEN WATER COMES ON, IT STALLS. BUT IF YOU PULL TRIGGER BACK ON WAND, THEN SPRAYER WORKS. THE MINUTE YOU LET GO OF TRIGGER, IT STALLS OUT.
ANSWER : Hi you have got a fault with the unloader it’s not unloading so its going a bove the 13amps and knocking the thermol overload out or blowing a fuse you could cable tie the trigger open or get a new unloader kit costing about £70.00 regards

Read Full Q/A … : Honda

2011 Honda crv starts up then stalls out within 3-5 seconds.
ANSWER : Your low oil sensor is bad or the oil is low. You can get a new sensor on eBay for pretty cheap.

Read Full Q/A … : Honda