ut water for a while then show IE error code. what will be the problem? thanks; willy
Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Samsung error 1E or 1C

This means that the water pressure or water level isn`t correct. First check whether the washing machine is properly connected to the water supply. The supply hose may be clogged or kinked. When this is the case, remove the kink.

If an adequate level of water does not fill the tub in a specified period, the [IE]/No Water Supply appears on the display of the washing machine.
If your washer is draining the water at the same time it is filling with water, please check the following: Make sure that the house drain pipe is at least 30 inches high. If so, check to make sure the drain hose is not pushed too far down into the drain.
Ensure the water taps are fully opened.

During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen. Once the temperature increases above freezing, the water supply will resume.

What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.
When a Clogged Filter Error (1E) occurs, it means the fine filter at the bottom of the dishwasher is dirty. You will need to clean the filter to clear this notification. For better washing performance, clean the filter at least once a month.
Start by running your washer through a drain cycle. Observe the washing machine as it pumps water into the hoses and up into the standpipe. If you see water back up and out of the standpipe, your washer`s drain is most likely the issue.
What causes a washing machine to not rinse properly? Washing machines not rinsing is a common issue and usually means that the washing machine is not draining correctly. This is usually due to the washing machine drain hose being bent or stretched or the drain pump filter being blocked.
Use a funnel to pour about a quarter of a cup of baking soda into the pipe. Next, empty a baster full of vinegar into the drain hose. Top tip: If the blockage is not completely gone, you can repeat the above process. Once you have cleared any debris from the hose, pour hot water in to flush everything out.
Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.
The Samsung washing machine error code DE indicates a door error, which means the door is not able to close properly. Make sure the door is properly closed, and if the problem persists, you`ll need to check the lock itself.
When a Clogged Filter Error (1E) occurs, it means the fine filter at the bottom of the dishwasher is dirty. You will need to clean the filter to clear this notification. For better washing performance, clean the filter at least once a month.
Codes LE, LC, E9, and LE1 mean the same thing: there is leakage or self-drainage of water from the tank in the Samsung washing machine.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have a pressure booster pump installed which turns on automatically when we open the tap and turns off by itself when we close the tap, but when power goes and comes back(common in india), the pump will turn on even with no tap opened and does not turn off automatically and goes on running, some kind of airlock problem I think, when we just shut off and on water input several times, it again starts working well
ANSWER : Check to see if the output pipe has water in it when the pump swutches off the pump needs to be primed at all time what we normally find cases like this is the pump is higher than the supply or there is an air pocket on the output where the pressure sensor is

Read Full Q/A … : Garden

I have a 1/2 horse wayne shallow well pump. At times the water in the house slows to a trickel. This will happen for about 40-120 seconds then the pump seems to kick on and the pressure is restored. I have replaced the high low switch and the problem persists. Please let me know any thoughts on the problem. Thank You
ANSWER : Check air in your water tank should be less than you’re cut in pressure..

Read Full Q/A … : Garden

The well pump is running, but no water is supplied to thr irrigation lines. once I put water in the pump housing by removing the pump guage the pump pumps water through the irrigation lines. when it shuts down, iloose the prime again. what should I do?
ANSWER : Sounds like you have an air leak. First check your fittings, next carefully run water over the pump seals (avoid getting water on the motor or you’ll hurt yourself and the pump if not worse) the pump will prime if the leaking seal is covered with water. Take your time and be careful and it should only be a matter of a loose fitting or simple seal swap.

Read Full Q/A … : Garden

The pump will not continue to run after starting, it runs for 5 seconds and then stops, until the next attempt to detect water, the pump is sitting in three feet of water. The pump will not continue to run after detecting water.
ANSWER : CLEAN AIR LOCK HOLE

Read Full Q/A … : Garden

Running pump stopped
ANSWER : I assume that the plug in is working properly. Always check power supply first. Is there a GFCI circuit that it is plugged into. Then check the pump to make certain it us turning. How long had it been on before unplugging it. It could be worn out. Sometimes it takes a jolt to start the motor again. How big is the motor. Possible bad capacitor. Could be a solid state motor, then it’s bad. Is it a magnetic motor, that could be turning the wrong way.

Read Full Q/A … : Garden

Leakin water pump
ANSWER : The water pump on a car has a bearing that blocks a hole when working. When the pump goes, it pulls the bearing from the hole and leaks. This is very common, and it was made this way for pin-pointing the issue. The water pump should be replaced.

Read Full Q/A … : Garden

I have a deep water well, it has not been used a lot in the last few years & the water is brown, can this problem be rectified
ANSWER : Hi Enslow, I can only guess that if the well hasn’t been in use for some time then it’s possible that if you run the pump and get brown water it may clear in time. My suggestion is simply continue to run the pump few a decent period of time that maybe a few days . As you do this take samples in say clear glass containers and see if there is improvement. So take samples every couple of hours and it will be apparent if the water is clearing or not. Make sure the pump is a decent distance from the bottom of the well.
Hope that helps
Regards
Steve

Read Full Q/A … : Garden

Pump runs for a few minutes becomes hot and stops then starts again
ANSWER : Pump motor is overheating or drawing too much current and the safety is shutting the motor down. After a period, it automatically kicks back in (quite common). Replace motor (and safety which probably comes with, or is actually contained inside motor).

:o).

Read Full Q/A … : Garden