ss26
Experienced gardeners share their insights in answering this question :
This is usually due to a carb issue. You can get carb kits from the dealer.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The air filter may be clogged. If the air filter is clogged, the engine will get too much fuel and not enough air. As a result, the engine may not start. If the air filter is clogged, replace it.
A clogged carburetor is most commonly caused by leaving fuel in the string trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to stall.
If the drive shaft is broken, the string trimmer head won`t spin. The drive shaft is not repairable—if the drive shaft is broken, you must replace it. Need help finding your model number? If the threads on the drive shaft are stripped, the trimmer head will not stay on the shaft.
The most common problem with a string trimmer is that the unit runs out of string. The string may also be twisted or loose on the spool. The cutting head may be dirty or the head outlet guide may be bent. An electric trimmer`s power cord, switch, or motor may fail.
When you go to operate the saw, and the saw does not operate, you might want to check out a few things: 1) Make sure the battery is fully charged. 2) Be sure that the battery is put into the saw correctly, and secured. 3) There might be debris on the battery, or inside the saw, where the battery connects.
If your 2-stroke brushcutter fails to start, the simplest explanation is that there is not enough fuel: in this case you simply need to top it up. A 2-stroke brushcutter engine runs on fuel/oil mixture, which you can buy ready prepared, such as EFCO-Mix Alkilate alkylated mixture in a 5 L can.
If your trimmer engine idles, but stalls on throttle, check the following parts: the gasket, primer bulb, fuel filter, air filter, fuel vent, fuel line, and carburetor. The repair and symptom guide will help you better identify the part needed to be replaced and how.
So, an air filter might clog over time. Once blocked with dust and debris, it cannot supply the required amount of oxygen to your trimmer` engine resulting in power loss. Find the air filter, take out this component, clean and reassemble it. Replace the part if you cannot reuse it.
If your RYOBI Edger isn`t starting: For 18V or 36V Battery models: check the battery has charge by pressing the fuel gauge. For AC models: turn the power point switch off and check the cord is inserted correctly in the extension lead. Use a heavy-duty extension lead no longer than 25m for optimal performance.
This can be due to corrosion, scratches or general wear. As a result, the cutting edges of the cutter comb of your blades are no longer sharp, reducing their ability to cut. Sharpening the blade is required to reface the cutting surfaces restore these sharp edges.
Over time, the spark arrestor can become clogged with soot. If the spark arrestor is clogged, the engine may stall or run roughly. To unclog the spark arrestor, remove it and clean it with a wire brush. You may also replace the spark arrestor.
The first thing to do is to ensure that the battery is fully charged. If after charging the battery you are still experiencing the problem, then it may indicate a fault with either the battery or charger. The defective item will need to be replaced.
The clutch engages the clutch pads to spin the trimmer head. If the clutch assembly is defective, the clutch will not disengage the clutch pads, and the trimmer head will continue to spin, even at low speeds. If the clutch is defective, replace it. (Note: some string trimmers do not have a clutch.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Strimmer wont start plug very dry when i remove it?
ANSWER : Sounds like the gas is not getting to the cylinder—remove carb and disassemble–make sure all jets are clear and the float valve moves freely.
Read Full Q/A … : ss26
My rcs5335s engine starts but wont keep running, its starts ok but fizzels out after a few seconds
ANSWER : May have to do carb adjustment
Read Full Q/A … : ss26
My Ryobi portable table saw BTS20 just quit working in the middle of a cut.
ANSWER : Me id look at the under side of saw , id bet the saw just tripped out in use and needs to be reset , id also bet the reset is marked in red some place around motor
Read Full Q/A … : ss26
Im having trouble starting my 2 stroke chainsaw. I follow the instructions but it wont fire over it sounds like its just about to but wont.
ANSWER : Here is a Link to one of my Tips:http://www.fixya.com/support/r6081405-cleaning_small_engie_carburetorGood Luck!Jim
Read Full Q/A … : ss26
Does not run, will start with starting fluid – Mantis 2-Cycle Tiller
ANSWER : You should never use starting fluid on this model.
Add a couple of ounces of 100% acetone (available at Walmart) to some fresh fuel. Attempt to start for several pulls. Let sit for several minutes and repeat until it sounds like it wants to run.
Then watch this video and do it:
http://www.alamia.us/mantis_parts_s/148.htm
Read Full Q/A … : ss26
It wont start,I replaced the spark plug
ANSWER : Joe try putting some fuel in where the spark plug goes. If it still doesn’t fire then proceed to eliminate things. Firstly the air filter will need cleaning then the spark coil. If it still don’t fire check the switch is ok. Sometimes the switch breaks a circuit and helps with the running of it.
Read Full Q/A … : ss26
I have aryobi bc 30 ry30562.engine does not come up to speed.feels like it is starving for fuel.when i start to weed whack it wont rev up.could this be a fuel problem?
ANSWER : You definitely do have a fuel problem try replacing your fuel filter
Read Full Q/A … : ss26
Wont stay running – Mtd 22" Yard Machine Push Mower
ANSWER : Under neath the carby is a single brass bolt, undo it
that one bolt is a multi jet, find four holes use a fine pin and carby cleaner ,hint one is at the top were the thread starts , one is in the inside center and two in the sides
put it back in and prim and start, hope it helps
Read Full Q/A … : ss26
