Clean your carburetor with carb clean and scrub with a tooth brush, lots of YouTube videos for instructions, and clean or replace your air filter.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If your lawn mower starts, runs for a while, then dies, check the ignition coil, gas cap, and spark plug. One or more of these parts could be causing your problem. Follow our repair and symptom guide to help you fix this.
If your lawnmower is starting and then stalling, the most likely issue is the carburetor. The most common issue is that the carburetor is dirty. Here`s what you need to know about how a dirty carburetor can cause a lawnmower to start, then stall out and die.
A full gas tank and oil reservoir are the essential first steps when checking why the lawn mower won`t stay running, but the problem could also be a dirty filter, clogged carburetor, improper fuel mixture, or a dirty spark plug.
The most common cause of a mower that runs for thirty minutes and then dies is a faulty armature. A faulty gas cap is the second most likely cause.
The spark plugs are worn or damaged If you find that your lawnmower keeps dying, or keeps stalling while cutting grass, then inspect the spark plugs. Look for signs of damage or wear. Something as simple as a cracked porcelain insulator can mean an electrode has been damaged or burned away.
Condensation inside the gas tank is one culprit, but moisture can also enter the system through a loose or ill fitting gas cap. The best solution is to drain the mower`s gas tank and refill it with fresh gasoline. A clogged fuel filter can also cause a mower engine to die.
The most common reason your car starts then dies immediately is because of a lack of fuel in the engine. This often happens because there is a small amount of fuel in the fuel rail, which helps to start the engine. However, there is no fuel pressure to keep the engine running.
A clogged carburetor is most commonly caused by leaving fuel in the lawn mower for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and prevent the engine from starting.
The most common reason for a surging lawn mower engine is a blockage in the fuel supply, but there are other possibilities: Bad gas. Bad spark plug. Dirty/faulty carburetor.
Other things that could cause this issue are bad fuel, weak/colapsed/kinked fuel line, faulty spark plug, faulty ignition/coil, oil over full, clogged air filter, plugged/dirty carburetor, worn engine parts internal rings/valves/etc.
A lawn mower that only runs with the choke on might be having problems with the carburetor, air supply, or bad fuel. Maintaining a clean carburetor will make the fuel delivery system run smoothly. Use high-quality fuel to extend the lawn mower`s life.
Other things that could cause this issue are bad fuel, weak/colapsed/kinked fuel line, faulty spark plug, faulty ignition/coil, oil over full, clogged air filter, plugged/dirty carburetor, worn engine parts internal rings/valves/etc.
Use Carburetor Cleaner Fortunately, you can generally do this without even taking the carburetor out of the engine. Start by purchasing some commercial lawnmower carburetor cleanerOpens a new window, which comes in a simple spray can and will make it easy to clean the inside and outside of the carb.
Chainsaw stalls Chainsaw is 4 years old and has a history of moderate use. After I ran the saw about 1 minute on plain gas (grabbed the wrong gas can – ouch) the chainsaw sputtered and stopped.
It didn't seize, and the pull starter never became more or less difficult than normal. The engine would continue to start if I pressed the prime bulb and engaging the choke, but stall again after 10-20 seconds. The temperature that day was about 50 degrees F and I was running the saw with the “cold plug” installed (per warm weather running).
When it refused to keep running I did the following:
Flushed the fuel tank (that's when I saw the gas had no oil in it).
Ran hardware wire through all of the fuel lines.
Replaced the fuel filter and spark plug.
Cleaned the air filter with a nylon brush and compressed air.
Same behavior (start then stall in less than 20 seconds). I made at least 20+ attempts to start it.
I removed the carburetor and, though it looked perfectly clean, I took off the top and bottom covers then sprayed everything with automotive carb cleaner and blew out the passages with compressed air. The gasket and diaphragm looked new. No pinholes in the diaphragm when held against a bright light. I reinstalled the carb but got the same behavior (start then stall in less than 20 seconds). I again made at least 20+ attempts to start it.
I disassembled the short block and saw that the piston has some slight scoring on it. The ring is clean and I verified that the piston ring has .001 clearance between it and the piston ring groove all the way around with the ring held tightly in place (I was thinking that the piston might have become deformed if it did indeed get too hot when run without any oil premix).
The cylinder wall has no scoring and there isn't any signs of melted aluminum anywhere. The crank is clean as was the inside of the crank cover.
I reinstalled the crank cover using permatex non-hardening gasket goop and torqued the cover bolts to 10 inch pounds. I reassembled everything else per the exploded diagrams in Echo's “parts manual” for the CS400.
During assembly I took note that both the carb gasket and intake boot look like new.
Still the same result: press prime bulb once, engage choke, pull a few times and it starts but stalls after 10-20 seconds.
I'm stumped.
ANSWER : Not sure what to say other than its fuel starvation, if not already done replace the fuel filter in the tank, if no better i would suspect a massive air leak, so replace the crank seals, if there is no primary compression in the crankcsae fuel will not pull through the engine, good luck.
