work but now nothing, any suggestions.
Garden
Experienced gardeners share their insights in answering this question :
Your electric clutch may need adjustment. Take the hood off. Look behind the double pulley that’s on the crank shaft. Behind the pulley is an electric clutch. You will need a .010-.015 feeler gage and check between the clutch plates. You will tighten the three screws that mount the clutch to the motor. Try and get as close to .010″ as you can. After adjustment start the motor and try and engage the pto. I bet it will work.
Good luck
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
If the PTO clutch is not receiving power, the clutch solenoid is defective, or the clutch itself is worn out, the blades will not engage. Since a PTO clutch is not repairable, you will need to replace a broken or worn out clutch with a new one.
The PTO switch is a critical safety device developed to prevent unintentional blade actuation of lawn equipment. This switch is part of a series of controls that comprise a mower`s safety interlock system, requiring riders to use proper procedure when operating machinery.
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
Powershift PTO engagement problems could be from blocked hoses or fittings, bad connections or ground or the solenoid. Mechanical PTO engagement problems could originate from low air pressure, improper cable installation or back lash too tight.
This operation is crucial to the overall functioning of riding mowers, and thus PTO clutch repair may need to be immediately performed on riding mower models that have a failed clutch. Fortunately, you can fix your clutch irrespective of your experience with PTO clutch installation.
Powershift PTO engagement problems could be from blocked hoses or fittings, bad connections or ground or the solenoid. Mechanical PTO engagement problems could originate from low air pressure, improper cable installation or back lash too tight.
Powershift PTO engagement problems could be from blocked hoses or fittings, bad connections or ground or the solenoid. Mechanical PTO engagement problems could originate from low air pressure, improper cable installation or back lash too tight.
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a Craftsman FS5500 48″ lawn mower. The PTO makes a noise (squeak) for a second when I pull up on the red blade engage knob. The blades do not engage. PTO does not turn. When I push the red button down to disengage there is a brief squeak from the PTO.
It worked well the past month then a little problem 2 weeks ago. It seemed to disengage after mowing a while. Then after sitting for 15 minutes the blades would engage. I used it earlier this week and the PTO won’t turn at all.
Just purchased from the last and original owner a month ago. He said the oil would need to be changed this summer. Could that be part of the problem? Engine runs great!
Also, I need an owners manual, not able to find from the previous owner.
Thanks
ANSWER : Hi,The problem is probably in the button that you pull and push to engaged and disengage the PTO… If you wiggle the button or try to pull it slowly, you may find a spot where it will work. But the button has gone bad and will need to be replaced.If you are comfortable with wiring, you could jumper the wires and getting it working, but it would be a very temporary and possibly dangerous fix…
Read Full Q/A … : Garden
Need the pto to work on a 6300 john deere tractor we have changed the fuses and changed the sencer on the back can you help
ANSWER : If you have tried a new sensor and a new switch the the next step is to replace the pto solenoid valve.If that proves fruitless then the b.c.u.needs to be replaced or bypassed.The solenoid valve will cure your problem 90% of the time.If that does not work,let me know,i can tell you how to by-pass the b.c.u..
Read Full Q/A … : Garden
When i engage my blades it won’t work could it be
ANSWER : Having the same problem and it seems on mine that tha blade engagement assemble is not fuctioning properly. Could be tha belt mine seems really loose. Im going 2 take another look tommorrow, and posssible replace tha belt.
Read Full Q/A … : Garden
Mower won’t start
ANSWER : This may sound stupid but don’t mean it to…
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.
Have you tried with the choke all the way open? Do you have an automatic cruise? Is the right (correct) pedal being pushed in? These will affect if it starts or not. Also if your drive belt or one of the other belts not being tight enough will affect if it starts or just turns over. Not too many things can stope it from starting with new/good battery AND if its getting gas. Try cleaning your gas line and obviously making sure there is no obstruction around or near your blade, if it does start with blade engaged that is :))
If it doesn’t start with blade engaged, well make sure it’s in neutral. Mine won’t start in reverse but will in forward or neutral.
Hope it helps.
Anthony
Read Full Q/A … : Garden
Blades wont operate when engaged – Craftsman 20 Hp 42" Deck Lawn Tractor
ANSWER : Check the PTO switch it may have worn out
Read Full Q/A … : Garden
While cutting grass the pto clutch cuts off, i have to push switch in and back out to restart blades. I have replaced the switch and pto clutch
ANSWER : Pto kicks in and out while mowing was wondering if its electrical or something else i have a jd 420
Read Full Q/A … : Garden
When hit switch pto won,t come on
ANSWER : Check the 2 wire conection under the frame near the pto clutch, motor off of course. Make um tight.
Read Full Q/A … : Garden
My cub cadet 2165 PTO clutch has no voltage getting to it to activate it. the normally closed switch is ok. could it be the relay? how do I test it?
ANSWER : On my cub the blades keep shutting down when im mowing . I replace the pto switch and it doesnt help .. got a recommendation
Read Full Q/A … : Garden
