Craftsman 36cc, 16 In. Gas Chain Saw

Experienced gardeners share their insights in answering this question :
Turn them both in , gently, till they bottom out and then back them out 1 1/2 turns. This will get you real close and then fine tune them from there. hope this helps.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Turn the high speed or main jet screw clockwise until the engine begins to slow. Then, turn the screw the other way until the engine begins to slow. Turn the screw back to the midpoint. Once adjusted, check engine acceleration by moving the throttle from idle to fast.
Or it won`t shift far enough, whatever you do to the cable tension. You need to adjust the high (H) and low (L) limit screws on the derailleur. Viewed from behind the bike, the H screw limits how far the derailleur can move to the right, while the L screw limits how far the derailleur can move to the left.
Husqvarna two stroke engines are designed to run on clean, fresh, unleaded petrol. A fuel / oil ratio of 50:1 is recommended for all Husqvarna 2-stroke products.
Product Summary. 2.2 cubic inch 36cc chain saw features 2.2 HP emergency and inertia chain brakes, low vibration, 3/8in. chain pitch, 13,000 maximum no load RPM.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Settings for low and high speed screws for carb for husqvarna 136
ANSWER : Turn them both in , gently, till they bottom out and then back them out 1 1/2 turns. This will get you real close and then fine tune them from there. hope this helps.

Carburetor problem How to adjust carburetor husqvarna 136?
ANSWER : HiHigh speed H=3\4 turnLow speedL=1 1/4 turnidle speed t adjust accordingly. regards savumihai71

Setting hi lo on 235 husqvarna – Husqvarna , No.455 Rancher, 20" Gas – Powered Chainsaw
ANSWER : You need a special tool to adjust the mixture screws, i have to say they are not easy to tune, you will also need a rev counter to set the high revs, it is very difficult to give basic settings for the carb as they vary greatly

Need to know what the carb adjustments are for a model 61 husky
ANSWER : Low side one turn out from bottem.high sie is the same.after saw is running readjust both high and low.make sure the side dosen’t go in any more then 3/4 of a turn out……if it does you will burn up the saw….

My saw is a 039 stihl how do I set the Carb back to factory setting it will only start with the choke on and then turns off
ANSWER : Hi, set the screws from lightly seated to 1.25 turns in the low and 1 turn on the high. Also check for perished impulse hose and fuel hose. Regards Phil.

Just bought a husqvarna 125 B blower at the end of last summer. It starts right up but when I give it the throttle, it bogs down and has no power. The fuel is fresh and clean and there is a new spark plug in it. I pulled the carb and made sure the ports were clear. Also checked the fuel line in the tank.

Is there a speed adjustment screw I should be looking at?

Any suggestions would be greatly appreciated.

ANSWER : Ajust the high speed carb screw or run on partial choke

The saw carb adjustment has a high and a low but they only turn haft turn how do i set them
ANSWER : If in the USA I would tell you to thank the EPA. I suspect you are in the UK, I do not know who to throw rocks at there. Some newer carburetors no longer have springs to maintain the needle settings, without the caps adjustment becomes a constant nightmare. There are tools available through eBay (search for Walbro tool).

Husky starting point “H” and “L” 1 turn CCW from lightly seated. If running and you just want to tweak it a little just follow this. it is the most helpful adjustment procedure I have found.
Carburetor Adjustment by Madsens.com
http://www.madsens1.com/saw%20carb%20tune.htm
CW is leaner; to lean will destroy the saw. If over tightened closed (CW) the adjustment screw faces are easily marred; marred adjustments are difficult to impossible to set properly.Clean the air filter; adjusting with a dirty filter can cause a run lean condition once cleaned and the saw run.
There are 2 wav (sound – idle & full – may not be highlighted) files that I find most helpful, I think you will too. HTH
Lou
Constant tweaking may be camouflaging an air leak. Pressure tests are the only sure way to diagnose those. Air leaks undetected may destroy your saw.

What are the settings for the zama carb on a 330 homelite chainsaw
ANSWER : 1 1/4 turns out. Then let it warm up and adjust in up to 1/8