25cc Gas Line Trimmer

Setting the operating rpm
Experienced gardeners share their insights in answering this question :
To identify the idle screw adjustment push in and and out with the gas throttle handle and look at the carburetor for a little finger that moves in unison with your movements. That finger comes to rest against a tapered screw – the latter is the idle adjustment. Clockwise increases the speed and vice versa. Adjust so unit runs smoothly at low speed – too slow and it will stall. Experiment.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Electric Whipper Snipper (31050) Available now

Specifications: Motor Type: 1100W. Operating RPM: 7500.

In general, the larger your landscape, the more powerful your trimmer should be to efficiently maintain it. Lawns up to 1/2 Acre: Cordless trimmers ranging from 20 to 40 volts work well. If there`s a power outlet within 100 feet of the lawn`s perimeter, consider a corded string trimmer.
If the engine is running fast (revving high):

Make sure that the choke is disengaged and the throttle hold has been reset by pressing the trigger. You can check the throttle cable to make sure there are no kinks found in it – however this requires a mechanical proficiency to strip down the machine uncovering the cable.

The acceptable operating speed range is 1800 to 3600 RPM. Idle speed is 1750 RPM. The manufacturer of the equipment on which the engine is used, specifies the top governed no load speed at which the engine may be operated. DO NOT EXCEED this speed.
Cordless trimmers are rated by voltage, from 18 V to 84 V. Gas trimmers are rated by engine displacement, from 20 cc to 50 cc. Gas trimmers are also available with two-cycle or four-cycle engines, the latter being more powerful. With these factors in mind, duty ratings might be a good way to choose a weed trimmer.
The run time of the trimmer is 10-15 minutes per battery on a fully charged battery. Battery run time may vary depending upon factors including but not limited to charging conditions, battery maintenance, storage and environmental conditions.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I want to apply scotts grub ex. With an earthway spreader, what setting should i use?
ANSWER : You have scot’s i want bayers grub killer

Read Full Q/A … : 25cc Gas Line Trimmer

What i s setting on scotts lawn pro spreader to spread lesco momentum force weed andfeed 21-0-11
ANSWER : You can normally gauge it from the size of the granuals i think it is between 6 and 7

Read Full Q/A … : 25cc Gas Line Trimmer

I have a hand held scotts spreader and i don’t know which setting to put it on.
ANSWER : The setting should be stated on the bag of whatever you are spreading. Use that setting…Good luck…Lee

Read Full Q/A … : 25cc Gas Line Trimmer

Need spark plug gap. and carb setting – Mantis 2-Cycle Tiller
ANSWER : Gap should be about .020 – Carb setting is adjusted while running – lo idle and hi – lo idle adjusted to the lowest RPM before it stalls or starts running rough, the hi is adjusted at full throttle for the smoothest / highest rpm

Read Full Q/A … : 25cc Gas Line Trimmer

What setting is used to apply 1/4 lb per 100 sq ft?
ANSWER : BigVin, normally the bag of seed tell what setting to put spreader on for its proper application, If not try it on #4 setting, it all depend on how fast you wind and walk with a hand spreader. Good Luck.

Read Full Q/A … : 25cc Gas Line Trimmer

What is spreader setting for scotts southern turf builder on my earthway ev-n.
ANSWER : 3/4 of all the way be sure to shut off before turning as u can clump fert in grass

Read Full Q/A … : 25cc Gas Line Trimmer

My setting range from 22 to 32… the lime says Scotts should be set on 4&1/2 to 6.
ANSWER : Use Scotts settings for Scotts products.

Read Full Q/A … : 25cc Gas Line Trimmer

I have an older scotts drop spreader, called a precision flow control model and do not know what settings to use with the Scotts turf builder I have purchased.
ANSWER : Hi,
The best way is to just place a small amount… like 5 lb in the hopper…start with it barely open and see how far you get,,, then compute from there what you need…
The settings they give you are guesamates at best and are often set to place too much… why not??? they are selling you a product!!

heatman101

Read Full Q/A … : 25cc Gas Line Trimmer