Garden

How and where do you hold the shaft so that you can remove and replace the starter pawl assembly on the echo weed eater?

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Luckily, replacing a starter is not a difficult task. In most cases, it`s a fairly simple process that anyone with basic car knowledge can do. Here`s everything you need to know about replacing a starter, step by step.
A pawl is a metal part that rests on the ratchet. As the ratchet rotates, the pawl drops onto each of the steps on the ratchet rim, preventing the ratchet from turning in the direction of the pawl. Sometimes a spring is used to keep the pawl in contact with the ratchet.
The spring is used to fix the pawl, and the pawl is used to catch the hub and rotate inward. The hook one with 90 degree hooks pointing away from the wheel need to “hook” it into the hole.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

How do I remove the clutch on an Echo chain saw??
ANSWER : Backwards to the rotation of the motor, all you need are basic tools to do this.

Read Full Q/A … : Garden

How do u remove the tire off a rear rotiller – Troy Bilt Mtd Tiller Wheel Tire 480×4008
ANSWER : Remove the pin that secures the wheel to the axle and remove the wheel. Sometimes the wheel will become rusted to the axle and can not be removed. Its best to leave it be. Attempting to beat the wheel off the axle runs the risk of causing internal damage to the transmission. Once the wheel is off, remove the valve and release the air then using your tire tools remove the tire.

Read Full Q/A … : Garden

How to remove deck on 1045 cub cadet to remove and sharpen blades
ANSWER : You should be able to remove the blades without removing the deckThey bolt on from underneath with either a single or double bolt set up90% + are single bolt

Read Full Q/A … : Garden

How to remove the clutch housing to insert new starter rope
ANSWER : I see that this machine has a 31cc engine with chrome-plated cylinder. I will now include the detailed instructions on how to remove the clutch and insert new starter rope.

Remove the tube that holds the flex-drive shaft from the front of the motor cover.Remove the rear engine cover. Remove the throttle cable from the carburetor. Mark and unplug any wires for the on/off switch that go to the ignition coil (underneath front cover) if possible. Now if you have pulled the driveshaft tube out of the way, the clutch drum is up next. Inside it, screwed into the very end of the engine’s crankshaft is a Torx #25 screw. Before you loosen it, you will have to lock up the engine. To do so, remove the spark plug. Pull on the starter until the piston is down, then insert a length of clean, soft rope into the engine. The engine will come up and compress the rope, thus locking it in place to allow clutch drum and clutch removal. Loosen the T-25 (Star bit or Torx head) screw inside the drum.. You may be able to remove it with a long thin-blade screwdriver also.It probably won’t come completely out…it is made this way. Next, remove the clutch. It is screwed onto a small threaded section of the crankshaft Removal is counterclockwise.. It will be pretty tight. To help, apply peneterating oil. Whack the ears of the clutch near the center with a hammer and a dull flat-blade chisel or a small piece of wood unless there are bolts. then use a wrench. It will turn counterclockwise for removal and there will probably be a removal direction arrow on it’s face. After getting that off, remove the Torx screws holding the cover to the engine. The starter unit should be mounted inside as it mates with the top of the flywheel to start the motor. Remember to preload tension (5-7 turns) on the starter unit. Make sure the handle is installed. Jam the unit with a screwdriver or vise grips so you can insert and tie off the new rope. Then remove jam device and let recoil pull your new rope into place while holding the handle. Reassemble and you are done. Disassembly requires Torx head drivers and a good flat-blade screwdriver. Post back if needed.

Read Full Q/A … : Garden

How do I remove the pulley from the bottom of the crankshaft?
ANSWER : Crankshaft of what? I see a picture of a riding mower, is that what your working on? If so, you need a pulley puller. You can get one from your local autoparts store like autozone usually for a refundable deposit.

Read Full Q/A … : Garden

Cannot remove mower blade pulley nut – John Deere 22HP VTwin 48" Riding Mower
ANSWER : I think its a left hand thread, you undo it clockwise (the “wrong” way)

Read Full Q/A … : Garden

How do you remove the clutch drum assembly for model #316.791890
ANSWER : After I removed the clutch drum – how do i remove the next part? It has a circular spring that is hel in place. Thanks

Read Full Q/A … : Garden

Cant remove clutch cover – Echo CS400 18" Chain Saw
ANSWER : Is the Chain brake engaged?

Read Full Q/A … : Garden