Garden
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If you decide to run a longer trimmer line, you need to completely remove the guard. If you only remove the blade, the trimmer line will get too long and get wrapped up in the guard. As the string wraps around the guard it increases the resistance on the engine and causes the engine to lose its power and RPMs.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Trimmer head line loading instruction – Husqvarna 28cc Gas Line Trimmer
ANSWER : 1. Remove the cap on the trimmer head, it unscrews.2.
The spool comes off, and on the inside of the spool there is a small
hole, this is where you will start your trimmer line. It it will hold it
in place while you wrap it. There is also arrows on the spool showing
the direction that you need to wrap your spool.3. Insert the
line in the hole and start to wrap the line in the directions of the
arrows, try to keep the line in rows, or else the line may bind and you
will have to do it all over again.4. Feed the line through the
retainer and reinstall the spool by lining up the retainer and the slot
on the outside portion on the trimmer head, the screw back on the
trimmer head and you will be ready to trim.
The spool comes off, and on the inside of the spool there is a small
hole, this is where you will start your trimmer line. It it will hold it
in place while you wrap it. There is also arrows on the spool showing
the direction that you need to wrap your spool.3. Insert the
line in the hole and start to wrap the line in the directions of the
arrows, try to keep the line in rows, or else the line may bind and you
will have to do it all over again.4. Feed the line through the
retainer and reinstall the spool by lining up the retainer and the slot
on the outside portion on the trimmer head, the screw back on the
trimmer head and you will be ready to trim.
Read Full Q/A … : Garden
I cant remove the spool to change the line. it appears to be stuck.
ANSWER : Well there is either a screw knob that must be unscrewed first, or you aren’t removing it correctly. Some just Pull/pop right off. Others must be pushed in and twisted (Like a child proof cap) usually in the opposite direction the line spins. Pull the cord a tiny bit to see which way it spins, then push down/in on the spool (its spring loaded) and twist opposite. Most of today’s trimmers will give you the spool like that. Putting it back on it simply the reverse action.
Read Full Q/A … : Garden
Where can I get a replacement bar and chain?
ANSWER : Most any power equipment shop
Read Full Q/A … : Garden
Bar attact bolt – Remington Electric Pole Saw
ANSWER : Try sears parts online
Read Full Q/A … : Garden
Auto feed doesn’t work
ANSWER : Take the end apart and make sure the line is not getting bound up or is not over filled to where it can not move freely
Read Full Q/A … : Garden
Can not get spool head apart to change line, tried pump pliers, pipe wrench, won’t unscrew!!
ANSWER : If you are sure that it screws on it may be a reverse threaded unit..
Read Full Q/A … : Garden
I have a Toro Electric weed eater and cannot get spool off to change.
ANSWER : Did you try using a flat screwdriver between the head and the bump knob?
Read Full Q/A … : Garden
Need to know how to wind trimmer line on trimmer
ANSWER : Depends on the trimmer, all heads are different. However, the majority of trimmers are wound as follows:
1. pop the top cover off the head, pull the spool out. It will be either single or double lined, they will be wound counter clock wise.
2. the end of each line goes out each of the seperate holes
3. slide spool back on and replace cover
www.ButlerPower.com
Read Full Q/A … : Garden
