Garden

Checked the obvious..plug & fuse

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

A defective spark plug or ignition coil may need to be replaced. Your power washer`s spark plug is essential to keep it running since it ignites the air/fuel mixture. If your spark plug is dirty, cracked, or defective, it could be the reason your power washer won`t start.
If the pressure washer does not start, then the first thing to check is the fuse in the plug. The reading you`re looking for is the same as it would be when connecting the two probes of the multimeter together (as you can see in the example of this video, this fuse is actually fine).
The most probable cause is a clogged pump filter. The pump filter should be cleaned every three months or when it`s clogged. This filter is installed to catch foreign objects like buttons or coins, and to prevent these items from entering the drain hose.
There could be small leaks, holes, or tears in your garden hose or high-pressure hose that are causing your pressure washer to lose pressure when you pull the trigger. If you find leaks, plug the holes or replace the hose, which should solve your pressure issues.
It depends on the pressure washing equipment you purchase. New pressure washers will be rated with a number of hours they should last. For example, if it is rated 500 hours and you use it fewer than 50 hours throughout the year then it will last you more than ten years as long as you keep it well maintained.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Low pressure Will not keep pressure
ANSWER : Faulty pump. check each valve for obstruction or fault

Read Full Q/A … : Garden

Has no pressure, builds up when not holding trigger on gun, but when i press trigger shoots of with pressure the nothing just water comes out.
ANSWER : Bad pump

Read Full Q/A … : Garden

This pressure washer will continue to build pressure when you let off the trigger. I have replaced the hose 3 times because the pump continues to pump until it blows the hose. The pump will not stop pumping!
ANSWER : You have a defective pressure release valve or someone has misadjusted.

Read Full Q/A … : Garden

Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works

Read Full Q/A … : Garden

1750 psi Electric Pressure Washer: My pressure washer is losing pressure and is pulsa…
ANSWER : If the pressure washer is pulsating then that is a sign of check valve failure. You may be able to clean of replace the check valves. Replacing the head is the wrong way to go. This is completely unnecessary. If you can tell me the model number of your pressure washer then I can assist you better in pointing you in the right direction.

Read Full Q/A … : Garden

I have used the McCulloch (FH180A) three times over the course of two years. On my fourth use the pressure washer just surged on and off and I would get a tiny spray from the gun each time it surged. In other words it would do nothing. Please help… very frustrated. Thanks
ANSWER : Sounds like the problem could be low input water flow or pressure. There could be crud on the intake where you hook up the garden hose, there could be some other sort of blockage. Try hooking it up to the hose and pull the trigger (with the power switched off) and wait to see if water comes out the tip. Also look at the tip(s) themselves. sometimes a piece of crud gets into the hose and then clogs the tip.

Read Full Q/A … : Garden

My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself.

Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount?

What should I do? Spark Plug? Turn wrenches?

Please let me know

ANSWER : You should be fine to take the recoil off, there shouldn’t be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won’t start unless there is enough oil in them. If your oil level is fine, check to make sure that your motor is getting spark.

Read Full Q/A … : Garden

How do i prime the pump on the soaper or chemical dispenser on my troy built 2550 psi pressure washer?
ANSWER : There is no need to prime. But you do need to use the black spray nozzle to get soap to siphon out.
if that doesn’t solve the problem let me know

Read Full Q/A … : Garden