Garden
Experienced gardeners share their insights in answering this question :
I need a little more accurate information. Also please post Model
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.
Check that all the safety switches are working correctly, it is possible the seat switch is bad or loose plug/ bad wire. Also if battery weak or charging system weak/faulty the clutch will stall out engine, charge battery up with charger and try.
Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.
It could be your bearings and your spindle pockets, or spindles, have seized up,” says Oshel. If the blades are stuck, pump some grease into the fitting and carefully work the blades back and forth by hand until they move freely.
(1) The blades should always be turned on at full throttle if the mower has a electric P.T.O. switch.
For power shift operation, when a power shift PTO is engaged, a solenoid is energized. Air or hydraulic fluid then compresses a clutch pack in the PTO. This locks the PTO output gear to the output shaft and allows work to be done. When the power shift PTO is disengaged, the solenoid de-energizes.
Pump trouble is usually characterized by increased noise, increased heat, erratic operation of cylinders, difficulty or inability to develop full output, decreased speed of cylinders or hydraulic motors, or failure of the system to work at all.
Pump trouble is usually characterized by increased noise, increased heat, erratic operation of cylinders, difficulty or inability to develop full output, decreased speed of cylinders or hydraulic motors, or failure of the system to work at all.
The PTO is engaged and disengaged using the main transmission clutch and a remote control mechanism which operates on the PTO itself. Typically, an air valve is used to engage the PTO, but a mechanical linkage, electric or hydraulic mechanism are also options.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
John deere stx 30 pto wont engage
ANSWER : Check your fuse or for a broken wire( or shorted)
Read Full Q/A … : Garden
Need the pto to work on a 6300 john deere tractor we have changed the fuses and changed the sencer on the back can you help
ANSWER : If you have tried a new sensor and a new switch the the next step is to replace the pto solenoid valve.If that proves fruitless then the b.c.u.needs to be replaced or bypassed.The solenoid valve will cure your problem 90% of the time.If that does not work,let me know,i can tell you how to by-pass the b.c.u..
Read Full Q/A … : Garden
My Tractor (425) won't start – John Deere 420,1020,2010,2020,2510,2520 Tractor Float
ANSWER : If you have no spark the first thing to replace the time delay module on the left rear side of engine. Its black and about 2 inches by 1 inch with yellow,red,orange and black wires going to it. Replacement is round shaped with same amount of wires.If no fuel to carb check for flow at filter, if theres flow but no pressure look for a split fuel line in tank between pump and sender.
Read Full Q/A … : Garden
The mower blades on my John Deere stx 38 lawn tractor will not engage. I just installed a new pto switch and when engaged the engine stops.
ANSWER : It sounds like the safety switch under seat is bad
Read Full Q/A … : Garden
Weak fire out of coil wire – John Deere Pto Clutch For Stx38 And Stx46 Lawn Mowers
ANSWER : This can be due to a dirty flywheel, an improper gap between the flywheel and coil, or a coil that is failing, first check for rust or dirty build up on the flywheel, then check for proper gap, and if neither of those are the issue, replace the coil
Read Full Q/A … : Garden
I am trying to find a new or second-hand bonnet for my john deer stx38. i live in the gippsland area. any suggestions?
ANSWER : I use www.greenpartstore.com
Read Full Q/A … : Garden
PTO CONTROLS. How do you engage and disengage PTO.
ANSWER : The tractor is not a 6300 is it.If it’ not you need to adjust the cable for the p.t.o. until it will stay down.Don’t turn the turnbuckle too much at a time because there is a fine line between the won’t engage and the won,t disengage adjustment.
Read Full Q/A … : Garden
Looking for information on a John Deere tractor S/N CH0850S017329 and the current estimated value of this tractor with approximately 2,700 hours on it.
ANSWER : Can you please post the model number of the tractor? Thanks
Read Full Q/A … : Garden
