Honda
Pressure washer honda gx390 13hp motor with electric start blows fuses
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
If the pressure washer trips the fuse board or blows the electrics in your home, make sure there`s no water in the switch or the other electrical items – and again examine the capacitor if your model carries one.
5 Amp Fuse for Aqua Blast® Pressure Washer Ignition.
Why Does My Appliance Keep Tripping the Breaker? An appliance that consistently trips your circuit breaker is not only annoying, it could be the sign of a bigger problem. The most likely reasons for this problem are an overloaded circuit, overheated appliance, electrical short, or ground fault issue.
Check the Fuse: If you have done all the repairs and replacements and your electric pressure washer is still not working, it may have something to do with the fuse. Inspect the fuse if it is blown or not. Replace the blown fuse with a new one and test the device again.
The number one cause of low or no pressure when using a pressure washer is a blocked or worn nozzle. Blocked nozzles will prevent water from escaping, while a worn nozzle will allow too much water to pass through, causing the pressure to drop.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
<!– from fixya rte –>Electrical diagram for Honda GX390 – Honda Gx390 Motor Inside Cover
ANSWER : Check out the manual here http://cdn.powerequipment.honda.com/engines/pdf/manuals/37Z5F602.pdf
Read Full Q/A … : Honda
My 13.0 honda gx390 motor has no spark and will not start
ANSWER : Try disconnecting the black wire which runs across under the fuel tank you should have spark.
Read Full Q/A … : Honda
Honda powwer boss 3000-whenyoupull the handale to spray it kills the engine
ANSWER : Sounds like the unloader (regulator). Try removing the nozzle, the pull the trigger with the engine running. If motor is still running then it could be the Unloader malfunctioning. If you require a new one try a bypass system for the unloader. The bypass will help save the life of the unloader.
Read Full Q/A … : Honda
Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works
Read Full Q/A … : Honda
My Honda 2600 psi power washer will not pull to start. It was running great then I allowed the neighbor to borrow it. He ran the washer till it was out of gas and proceeded to refuel and at this point it would no longer start. The pull cord is out about 4-6 inches out and I am concerned about taking the casing off myself.
Fearing that it may throw more off on the unit. If i take the casing off are there any spring loaded parts that will dismount?
What should I do? Spark Plug? Turn wrenches?
Please let me know
ANSWER : You should be fine to take the recoil off, there shouldn’t be anything that shoots out at you. You might want to check the oil level on the engine, many of the Honda engines won’t start unless there is enough oil in them. If your oil level is fine, check to make sure that your motor is getting spark.
Read Full Q/A … : Honda
My Honda pressure washer is leaking out of the thermal relief valve and I am looking for a part,I also do not have the manual. The model number is WGC 3030 and it is 3.0 gpm 9.0HP. The number on the thermal valve is 33120004,where can I find a part?
ANSWER : Does the thermal valve just screw into the pump head, if so what size thread is it? I have 1/4, 3/8, 1/2 in stock.
Read Full Q/A … : Honda
<!– from fixya rte –>Rope pull start is stuck, won't pull out – Honda Black Max 2600 PSI Pressure Washer
ANSWER : Check the oil level, if it’s very low or burnt then it may have siezed up internally.
It could also be that be that the cylinder is filled with oil or fuel.
if the washer was tipped over the fuel or oil may have migrated in to the piston combustion area.
It could also be that be that the cylinder is filled with oil or fuel.
if the washer was tipped over the fuel or oil may have migrated in to the piston combustion area.
Read Full Q/A … : Honda
Honda gc 190 starts then floods and stops. Wont start again till plug is taken out and dried then repeats same thing
ANSWER : Float level or a sticking needle valve, check float level as if it is adjusted incorrectly it can cause the main jet to allow fuel to flood through, the needle valve can do the same.
Read Full Q/A … : Honda
