e and then the water is discharged. Will switch off but does not activate next time.
Garden

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

No water jet from the nozzle of the pressure washer > check if the nozzle itself is not clogged – if this is the case, clean or replace it. Also check if the water mains tap is correctly opened and that there is no problem in the flow of the suction hose.
There could be small leaks, holes, or tears in your garden hose or high-pressure hose that are causing your pressure washer to lose pressure when you pull the trigger. If you find leaks, plug the holes or replace the hose, which should solve your pressure issues.
If there`s a low/no consistent stream of water:

The line needs to be “primed” before each initial use. Check the nozzle is clear. Use the supplied cleaning tool to check and clean the nozzle.

How Do I Tell If My Unloader Valve is Bad? In most occurrences, the first symptom of an unloader valve going bad is no pressure from the wand when the trigger is pressed. This happens when the unloader valve gets stuck open and does not allow water to enter the hose and trigger.
Clean the inside of the nozzles using a pin

If you have a needle pin, you can use it to clean the inside of the nozzles. Simply poke the pin inside the nozzle a few times until it no longer comes out dirty. Getting the pin hot first, either with a torch or hot water, can help break away any hard-packed clogs.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

No pressure Pump reassembly. I purchased a new pump and installed it. Got machine back together and I’m not getting any pressure. What would be the signs if I don’t have the shaft key in properly? Or any other suggestions?
Water comes out of nozzle with pressure for a quick second then no pressure, just water. This is a brand new pump so was curious if I installed it wrong. Wondering before taking it apart again.
ANSWER : No pressure would be a sign that the key was not in properly.

Read Full Q/A … : Garden

Kranzle electric washer will not suck up soap
ANSWER : Hi, if it has a chemical injector on the machine then the pressure at the lance will have to be lowered for it to pull in soap. it works on a similar principle to how carburetors on cars pull in fuel, bernouli principle. high pressure at one side of an orifice going to low pressure at the other side which causes a negative pressure ( vacuum) which should pull in the soap. there should be a non return valve at the orifice (hole) which prevents the water back feeding into the soap container, it is quite common for this valve to get stuck, it is just a ball, spring and o ring , and the ball sticks to the o ring. if it is this system then take the soap pick up pipe off the injector and just push the ball off it’s seat with a bit of wire.If it is a high pressure soap system then that is different, but they usually work with an injector in my experience.try taking the high pressure hose off the front off the machine and running it, if it has an injector on it it should pull in plenty off soap.hope this helps ,andy

Read Full Q/A … : Garden

When pressure washer engine is running and hooked to water supply, there is no water spray with trigger is depressed
ANSWER : Hi Have you checked that your nozzle in the lance end is not blocked. Please try this and then try without the high pressure hose attached.

Read Full Q/A … : Garden

Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works

Read Full Q/A … : Garden

Has no pressure, builds up when not holding trigger on gun, but when i press trigger shoots of with pressure the nothing just water comes out.
ANSWER : Bad pump

Read Full Q/A … : Garden

1750 psi Electric Pressure Washer: My pressure washer is losing pressure and is pulsa…
ANSWER : If the pressure washer is pulsating then that is a sign of check valve failure. You may be able to clean of replace the check valves. Replacing the head is the wrong way to go. This is completely unnecessary. If you can tell me the model number of your pressure washer then I can assist you better in pointing you in the right direction.

Read Full Q/A … : Garden

Honda powwer boss 3000-whenyoupull the handale to spray it kills the engine
ANSWER : Sounds like the unloader (regulator). Try removing the nozzle, the pull the trigger with the engine running. If motor is still running then it could be the Unloader malfunctioning. If you require a new one try a bypass system for the unloader. The bypass will help save the life of the unloader.

Read Full Q/A … : Garden

Starts great and sprays great, but will not continue to run when [ stop spraying. It locks up until I release the pressure from the gun.is there a pressure by-pass adjustment I can make?
ANSWER : Tune up motor, replace air filter/spark plug and oil.

Read Full Q/A … : Garden