Ryobi

Powerhead starts and runs fine but no matter which expand-it tool I attach they will not work. The blower won't blow. The edger blade will not turn. They trimmer will not spin.
Experienced gardeners share their insights in answering this question :
Hi Jim Kamph…You have a broken drive cable inside of the trimmer.You will need to replace the drive cablePlease rate meBud

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The air filter may be clogged. If the air filter is clogged, the engine will get too much fuel and not enough air. As a result, the engine may not start. If the air filter is clogged, replace it.
If your RYOBI Edger isn`t starting: For 18V or 36V Battery models: check the battery has charge by pressing the fuel gauge. For AC models: turn the power point switch off and check the cord is inserted correctly in the extension lead. Use a heavy-duty extension lead no longer than 25m for optimal performance.
The most common problem with a string trimmer is that the unit runs out of string. The string may also be twisted or loose on the spool. The cutting head may be dirty or the head outlet guide may be bent. An electric trimmer`s power cord, switch, or motor may fail.
The trimmer line might be the wrong size. If the trimmer line is too thick or too thin for the trimmer head, the trimmer line won`t feed. Make sure you are using the correct trimmer line for your string trimmer.
Over time, the spark arrestor can become clogged with soot. If the spark arrestor is clogged, the edger may stall or run roughly. To unclog the spark arrestor, remove it and clean it with a wire brush. You can also replace the spark arrestor.
If the battery is fully charged and the grinder still won`t turn on, your battery may be inserted incorrectly. The battery needs to be flush with the bottom of the handle, and should click into place.
If your 2-stroke brushcutter fails to start, the simplest explanation is that there is not enough fuel: in this case you simply need to top it up. A 2-stroke brushcutter engine runs on fuel/oil mixture, which you can buy ready prepared, such as EFCO-Mix Alkilate alkylated mixture in a 5 L can.
The most common problem with a strimmer not starting is that there`s a problem with the fuel mix. Double check that you`ve used 40 parts fresh unleaded petrol to 1 part 2-stroke oil (40:1). Check the petrol you`ve used isn`t stale.
When you go to operate the saw, and the saw does not operate, you might want to check out a few things: 1) Make sure the battery is fully charged. 2) Be sure that the battery is put into the saw correctly, and secured. 3) There might be debris on the battery, or inside the saw, where the battery connects.
The reason the grinder won`t work is that it`s most likely to be blocked or that there are beans compressed so tightly between the burrs that the motor can no longer turn them. This is user error.To attend to this, you will need to adjust the grinder to very coarse and operate it.
If the grinder does not run, the motor shaft may be frozen. Disassemble the grinder, clean the shaft and lubricate each bearing point with one or two drops of lightweight machine oil. Rotate the shaft to evenly distribute the oil. If the grinder still does not operate, the thermal limiter may be burned out.
Worn flanges will have a problem gripping the grinding disc, preventing it from spinning or slipping. As flanges wear, replace them as maintenance. Remove the lock nut, the outer flange, grinding disc and inner flange. Reinstall with a new inner flange, grinding disc and inner flange.
The first thing to do is to ensure that the battery is fully charged. If after charging the battery you are still experiencing the problem, then it may indicate a fault with either the battery or charger. The defective item will need to be replaced.
Checking for debris or damaged blades: Visually inspect the blades and confirm there is no debris stopping the blades from moving. If there is debris ensure the machine is powered off when removing any blockages. Check the blades for any damage as a damaged cutting blade could cause the machine to stop working.
The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the string trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance.
You need to ensure the battery is fully charged and the charger is correctly connected during the charging process. Another fault which can cause your Gtech trimmer not to work is the safety switch in the handle. To check it is operating correctly listen for a `click` when it is pressed.
Fuel Vein Blockage

Eventually the blockage can cause a complete stoppage of fuel going into the engine, therefore causing it bog down and stop. If you suspect you have a blockage, the best cause of action is to strip down the carburettor and blow down the fuel veins with an air line or air blower.

If your 2-stroke brushcutter fails to start, the simplest explanation is that there is not enough fuel: in this case you simply need to top it up. A 2-stroke brushcutter engine runs on fuel/oil mixture, which you can buy ready prepared, such as EFCO-Mix Alkilate alkylated mixture in a 5 L can.
Turn on the ignition switch and pull the starting cord quickly. You should see a spark in the plug gap. Since the spark may be faint, it may help to do the test in a dark area. If there is no spark, check for a broken or shorted (bare) lead wire or bad switch.
If your 2-stroke brushcutter fails to start, the simplest explanation is that there is not enough fuel: in this case you simply need to top it up. A 2-stroke brushcutter engine runs on fuel/oil mixture, which you can buy ready prepared, such as EFCO-Mix Alkilate alkylated mixture in a 5 L can.
You need to ensure the battery is fully charged and the charger is correctly connected during the charging process. Another fault which can cause your Gtech trimmer not to work is the safety switch in the handle. To check it is operating correctly listen for a `click` when it is pressed.
You need to ensure the battery is fully charged and the charger is correctly connected during the charging process. Another fault which can cause your Gtech trimmer not to work is the safety switch in the handle. To check it is operating correctly listen for a `click` when it is pressed.
Worn clutch – Since the string trimmer clutch engages with one or more drive shafts attached to the trimmer head to rotate the head when the throttle trigger is depressed, a worn-out clutch may prevent the trimmer head from spinning. A new clutch assembly is relatively inexpensive and easy to install.
Worn clutch – Since the string trimmer clutch engages with one or more drive shafts attached to the trimmer head to rotate the head when the throttle trigger is depressed, a worn-out clutch may prevent the trimmer head from spinning. A new clutch assembly is relatively inexpensive and easy to install.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Seems to start easily run for a few minutes and then slow and stop–bulb remains full –gas is good–have tried half choke in case too lean–did not solve–also seems possibly related to the angle I hold it at–seems to cut out quicker if blower tube angled more downward.
ANSWER : Your filter may be hanging up in the tank. you also my be losing compression

Read Full Q/A … : Ryobi

Will only develop power (and run somewhat properly) when the choke is engaged about 90%. Starts fine.
ANSWER : Sounds to me as tho you may have a loose carburetor or another part that is letting air into the system. Check all bolts and screws for tightness. Also, you may need to clean the carburetor or put some cleaner in your gas. Not too much, only about a tablespoon, but check the screws/bolts first.

Read Full Q/A … : Ryobi

Echo pb500 only runs with choke open – Echo Gas Blower 162 MPH 450 CFM Blower PB500T
ANSWER : I’m not to sure about the question. But you say it runs with the chock open. Your engine will only run with the chock open. Can you clarify?

Read Full Q/A … : Ryobi

Want run unless choke remains on – Stihl Bg72 Leaf Blower Intake
ANSWER : Probably fuel starvation.Wrong fuel air mix settings on the carb. Damaged carb diaphragm.

Read Full Q/A … : Ryobi

Won't start – Echo Pb – 413t Backpack Blower
ANSWER : Adjust the carb,altitude can effect the engine

Read Full Q/A … : Ryobi

My blower only runs with 3/4 choke even after warm up.
ANSWER : Look on the carb for 2 screws side by side. where those screws go into the carb, it will be stamped with an “H” and “L”. Open the screw that is next to the “H”, counterclockwise about 1/4 turn at a time with the engine running, that should solve it.

Read Full Q/A … : Ryobi

I have a new echo PB250 Leaf blower and it will not keep running. It starts fine but shuts off after a few seconds.
ANSWER : Sounds like a dirty carb, dissamble it and rinse good with carb clean, be careful when taking the top off it that you get it back together the same spray the white center good and all little holes good. then reassemble, also try to loosen your gas cap maybe first before cleaning carb, you might have a plugged vent in the line coming out of the tank. Good Luck

Read Full Q/A … : Ryobi

Hitachi rb24eap blower won’t stay running
ANSWER : Check your air filter is not clogged. Clean or replace as necessary.
It is a grey sponge ring that is located behind the cover plate near the priming bulb.

Read Full Q/A … : Ryobi

My name is June Strandberg, and I am a florist and gardener in San Francisco. I have been working in the industry for five years, and I love helping people find the perfect floral arrangement for their special occasions. I am also skilled in troubleshooting and fixing gardening tools, so if you are ever having trouble with your tools, please don't hesitate to reach out to me.