ill not stay going, my guess is that it is not getting gas into the carburator, also what is the spark plug gap?
Garden

Experienced gardeners share their insights in answering this question :
Hi there, it’s not a carb problem.That is to say, only the inlet gasket could be the problem.Otherwise, the problem is the gap between, either the plug, or between the contact and the magneto.One of those spaces need closing or opening, et voila.Don’t forget to help Me, by giving a rating,& good luck with that.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If the chainsaw won`t start, or starts and then stops and you find the spark plug wet with fuel mixture, it means that the engine is flooded (you will probably smell petrol). It happens when too much fuel enters the combustion chamber, possibly because you have pressed the primer many times.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
If your electric chainsaw won`t start, try examining it for these issues: Not pressing the safety button at the same time as the trigger. Tripped electrical breaker (for corded chainsaws) Frayed or damaged electrical cord (for corded chainsaws)
My chain saw starts and then dies what is wrong? This could be a number of things and is most likely fuel or storage related. Over a short period of time, fuel will become stale. If the unit is stored with stale gasoline, the system will become clogged or restricted.
One tell-tale sign that a chainsaw has flooded is the smell of fresh petrol near the muffler. To ascertain whether this is indeed the problem, simply disassemble the part, pull the starter cord as if you were switching on the engine, then dry it, reassemble it and try switching it on again.
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel will evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and prevent the engine from starting.
If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged. If this is the case, clean it with a wire brush.
1. Dull chain and or improper lubrication to the bar and chain, sharpen and or clean the bars oil holes. 2. Air filter and fuel filter for restrictions and contamination, clean or replace as needed.
You can find Poulan Pro products both in-store and online at home improvement retailers, hardware stores, and mass merchants all over North America. We are here to help you tackle… ANY YARD.
BATTERY LIFE PER BATTERY CHARGE

For example, a STIHL MSA 120 C-B chainsaw with the recommended AK 20 battery lasts for up to 40 minutes or can achieve a battery life of up to 55 minutes when equipped with an AK 30 battery.

If the filter becomes clogged, not enough fuel will reach the engine for it to run properly. Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle.
The two most common reasons a chainsaw won`t idle are a blocked air filter and an idle screw out of adjustment. Other possible causes include: Dirty Air Filter. Idle Screw out of Adjustment.
Oil, dirt, and debris can block them, preventing the air from flowing into the engine. If the idle port of your chainsaw gets blocked or damaged, your chainsaw won`t stay running. Check the idle port for damage or blockage. If it`s blocked, you can clean it using alcohol, kerosene, or any solvent.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

What is the spark plug gap for a NGK BPM8Y – Echo Cs-400 Chainsaws
ANSWER : 20-25 thou which is around 0.6mm

Read Full Q/A … : Garden

What spark plug (make, number) can I get for a Poulan 2025 chainsaw and what gap?
ANSWER : Replace with Champion CJ-7Y or RCJ–7Y sparkplug and tighten securely with a 3/4 inchsocket wrench. Spark plug gap should be0.025 inchesR stands for resistor on the RCJ-7Y. Either plug will work.PDF of Owners ManualIf you have other questions about your saw, there is an 800# at the top of PDF. Hope this helps.

Read Full Q/A … : Garden

I need a spark plug gap
ANSWER : 0.5mm or .02″

Read Full Q/A … : Garden

<!– from fixya rte –>Spark plug gap setting poulan pro 033. – Poulan Pro Prod/Poulan Weedeater Poulan Pro PP5020AV 20" Gas Chain Saw
ANSWER : .025″ plug gap

Read Full Q/A … : Garden

What should the spark plug gap be on a weedeater trimmer 25cc
ANSWER : Set it at .025

Read Full Q/A … : Garden

I need the spark plug gap for an Ariens ST624E. the spark plug = 21533500
ANSWER : The recommended setting is .030″

Read Full Q/A … : Garden

What is theair gap setting poulan 2150 2.1c i
ANSWER : .025″ or .6MM is the spark plug gap I assume air gap is what you were referring to is spark plug?

Read Full Q/A … : Garden

Plug gapping geo tracker – Champion International Champion& Small Engine Spark Plug 8 Pack
ANSWER : Normally is .030″ however Due to the variety of engine and equipment configurations, your best source for spark plug information is your engine or equipment operator manual. download from www.fitness.manualsonline.com
God bless you

Read Full Q/A … : Garden