Wild Thing 2375 18″ Gas Chain Saw 2.5 Cuin

Both saws have run well for years. Started to have carb problems with both. Rebuilt carbs on both saws, would run ok for awhile. Replaced fuel lines, new plugs never got any better. Purchased a new carb for both saws, thought they just had worn out carbs. With a new carb the Wild Thing run good for a few days. Now with a new carb they will both crank and try to run, but act like they are sucking air or have a crack in the case. Have the Wood Shark took a part, have not found anything. Cold they be sucking air at the base gaskets or at the bearings? Are they a rebuild kit? Would it co
Experienced gardeners share their insights in answering this question :
They could be sucking gas from the base gasket, head gasket or the bearings. Also, Check your flywheel very wheel and your armuter, if either are rusty then they need some sand paper to help create spark. There are rebuild kits and they are cheap. I always tell my customers to fix there older machines cause the new ones are **** and they leak everywhere and if anything brakes they are REALLY expensive to repair. You can get a rebuild kit whole machine for about 65 dollars

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Bar, Model# P4018WT.
A: The spark plug gap on all products is . 025-inch.
The company was acquired by Emerson Electric in 1972, and was purchased by Electrolux in 1984.
If your chainsaw still starts and then stops working, check the air filter. Clean or replace the air filter if it is dirty or damaged. Another reason that your chainsaw starts and then stops working could be that the spark arrestor is dirty or clogged. If this is the case, clean it with a wire brush.
For more than seven decades, Poulan Pro has been making outdoor power equipment homeowners can rely on year after year. Our products are built with pride in our factories in McRae, Georgia, Nashville, Arkansas and Orangeburg, SC.
Where are Poulan Chainsaws Made? Poulan chainsaws might come from many countries, though the labels say “Made in Sweden” or “Made in the USA.” Husqvarna has facilities in Sweden, Germany, Brazil, France, China, and the USA.
The fuel line may be clogged from stale fuel deposits, more reasons to cause your chainsaw to cut out when applying throttle. If a fuel line is cracked, it will leak gasoline and draw air from outside into the fuel line. If the line is leaking fuel, it needs to be replaced.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I cant ajust the h l on the saw and the saw is flooding out what do i use to ajust the pins this is a wild thing chain saw
ANSWER : The jet screws have a spline, there is a special tool to adjust these, part no. 530035560

I have a Poulan wild thing 4018. Just replaced the main frame. Had to take apart the whole saw almost. Now the saw will crank but runs at very high speed for a few seconds and then quits. I can goose the throttle a little to keep it running longer but dies eventually. What could be the problem? I have had the cylinder and piston out but didn’t touch the carb. Thanks
ANSWER : Make sure youmhave connected the primer hoses correctly, the shorter of the two connections on the back of the primer ( suction ) goes to the carb, this pulls fuel from the carb, the longer connection dumps fuel back to the tank, if you removed the cylinder end cap, you need to re seal this to the cylinder with instant gasket, also make sure the air tube between the cylinder and carb is correctly seated.

LEAKS FUEL OUT IMMEDIATELY – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Gas tank is cracked.

Adjustment for coil. how many thousands of " – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Most coil to flywheel adjustment is fixed by the mounting screws
it will be around .002″ or have clearance as close to the flywheel without touching it as contact is a dead short

What is the gas oil ratio – Poulan Wild Thing 2375 18" Gas Chain Saw 2.5 Cuin
ANSWER : Half and half

Need to have a manual on this wild thing so that i know the right ratios for the gas.
ANSWER : This Chain Saw requires a 40:1 gasoline to oil mixture. This is typical for all 2-cycle motors. More information can be found here:

http://www.ehow.com/how_4464807_fuel-poulan-wild-thing-chain.html

Will not start. changed to a new plug. Plug does have a spark. Seems to be getting gas as the more I pull the rope the more gas collects in the cylindar. Last spring I loaned it to a friend. Last summer I ran it briefly & it was idling extremely fast. I changed the gas before I tried to start it. Could the idle be messed up ? Idle Screw What is the approximate counter clockwise turns to get the idle in the “ballpark” to run ?
ANSWER : Better check friend might not have added oil to gas and it scored the cylinder wall

Fuel Mixture for a Poulan Wild Thing
ANSWER : As far as i know it is 1:40, or 3.2 ounce Oil to 1 Gallon unleaded regular fuel