Poulan
Experienced gardeners share their insights in answering this question :
FAQ Trimmers ‘ Poulan Pro
www.poulanpro.com > Customer Support > FAQ
If the unit has an on/off switch, move it to the on position (usually indicated by the … This should happen between 1-6 pulls, but no more than 6 pulls. 7. … Some units use a carburetor which does not require holding the throttle trigger. … If you smell fuel after following the starting procedure, assume the engine is flooded.
Poulan Pro Trimmer dies when I give it gas.? ‘ Yahoo Answers
https://answers.yahoo.com/question/index?qid…
May 22, 2007 – If you remove the two springs holding that cover on the muffler off you can … Put it all back together and you should be able to crank up and cut. … Poulantimmer PPB 100 JUNK, since new hard to start cannot keep running … If, it sit with fuel in the carb then it may still need cleaned with some Carb Spray.
[PDF]OM, PPB150E, 2007-01, TRIMMERS/EDGERS – Poulan
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The carburetor might be clogged. A clogged carburetor is most commonly caused by leaving fuel in the string trimmer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance.
If your trimmer engine idles, but stalls on throttle, check the following parts: the gasket, primer bulb, fuel filter, air filter, fuel vent, fuel line, and carburetor. The repair and symptom guide will help you better identify the part needed to be replaced and how.
The air filter or exhaust port may be blocked. The trimmer may need lubrication and cooling fins or air passages may be blocked. A cordless trimmer`s battery or charger may be faulty.
A worn, dirty, oily, or improperly gapped spark plug can cause a weakThe job of the spark plug is to ignite the air/fuel mixture. A worn, dirty, oily, or improperly gapped spark plug can cause a weak spark, which can misfire or detonate and cause a loss of power.
Sometimes the spark arrestor screen can become clogged up itself. Common symptoms include lack of power, especially under load; poor acceleration; engine won`t come up to full RPM; and higher than normal “spit back” through the carburetor.
So, an air filter might clog over time. Once blocked with dust and debris, it cannot supply the required amount of oxygen to your trimmer` engine resulting in power loss. Find the air filter, take out this component, clean and reassemble it. Replace the part if you cannot reuse it.
So, an air filter might clog over time. Once blocked with dust and debris, it cannot supply the required amount of oxygen to your trimmer` engine resulting in power loss. Find the air filter, take out this component, clean and reassemble it. Replace the part if you cannot reuse it.
The most common problem with a strimmer not starting is that there`s a problem with the fuel mix. Double check that you`ve used 40 parts fresh unleaded petrol to 1 part 2-stroke oil (40:1). Check the petrol you`ve used isn`t stale.
A: The spark plug gap on all products is . 025-inch.
The most common problem with a strimmer not starting is that there`s a problem with the fuel mix. Double check that you`ve used 40 parts fresh unleaded petrol to 1 part 2-stroke oil (40:1). Check the petrol you`ve used isn`t stale.
Clean the clipper to remove any hair clipping or grease accumulation. Place your new blades on the clipper and screw them loosely. Align your blades and hold them in place using your other hand. Gently, tighten the clipper`s screws simultaneously to maintain blade alignment.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
MY POULAN PRO 6.5 WONT START….nEED TO REPLACE SPARL PLUG BUT DO NOT KNOW ‘right one”..
ANSWER : Take the old plug out, any auto store should be able to match it up.
Gary
Poulan pro 42 cc, no spark – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Try diss connecting the earth cut out wire from the ignition unit and try for a spark again, this will rule out the switch and any trapped wires, re set the air gap between the unit and the flywheel to 0.3mm, if there is still no spark the unit is bad and will require replacment, they are normally only held on with a couple of allen screws, and either bolted to the cylinder or the crankcase.
My poulan pro 42cc is hard to start ,,, its1 year old an i’m not sure if its worn out from alot of use or if its with the ignition
ANSWER : Throw it out and buy a new one this is a throw away scoiety we live in due to cheap *** chinese **** oh yeah go green
Won't start – Poulan Pro Super Blowervacuum
ANSWER : Try turning the carb screw all the way in and back out 1 1/4 turns.
Poulan chainsaw 18″ 42 cc, pro gas filler cap?
ANSWER : Yep they swell after a while and will not screw in or out!
Sand the threads down so that the circumference is reduced with a course file or plumbers cloth, chamfer the threads a bit on the edges. A new one will do the same thing after a while so just fix the one you have.
Poulan blower was running – ran out of gas – put gas in – won’t start- primed – won’t start – let sit – won’t start-took cover off – sprayed starter fluid in carb – won’t start- -(very little stutter) won’t start-set overnight – repea -twon’t start-wits end !!!
ANSWER : Hello
Does it use a fuel and oil mixture?You probably did that.
Try removing the spark plug and cleaning it with a wire brush or some emery cloth.Make sure you have spark by connecting the plug wire and resting the plug on the metal motor block.
Do not hold the plug in your hand ,if you have no spark you may have a bad magneto.
Poulan Pro snow thrower PR8P27ES Brand new and unable to pull recoil handle or turn over with electric start. is anyone aware of a safty mechenism.
ANSWER : No known safety- did you assemble anything? if not- return it. if you did asssemble anything- slowly go back thru in reverse and see if you have a bolt in wrong
Fuel mixture for poulan pro heavy duty brushcutter 331 sn 01254n500330-1is needed asap. lost my manual!!!!!
ANSWER : 40:1 mix, 3.2 oz of 2 stroke oil for every gallon of gas.
Link to the manual is below
http://www.poulanpro.com/ddoc/POUO/POUO2001_USen/POUO2001_USen__530088910.pdf
