Poulan

Experienced gardeners share their insights in answering this question :
Check the fuel filter, air filter, and muffler for plugging. Check the fuel lines for decay or other damage. Remove the carburetor, clean it inside and out with spray carburetor cleaner. Check the lower chamber diaphragm for flexibility and no damage. Check the impulse passage that comes from the crankcase, through gaskets and heat insulator, to the base of the carburetor. Does the primer bulb pump fuel into itself after several pumps? Hope some of this helps!

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Q: How do I mix gas and oil? A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio.
In the case that your chainsaw runs for a while, then dies, it may be possible to simply clean the air filter to correct this symptom. However, a damaged air filter should be replaced. Regular checks of the air filter for buildup should be part of your regular chainsaw maintenance routine.
The carburetor might be clogged and needs to be cleaned.

A chainsaw`s carburetor mixes air and fuel to start the internal combustion engine. If fuel has been left in the engine for too long, it can become sticky and clog the carburetor, preventing it from starting. If the clog is minor, clean out the carburetor.

Most vehicles have rubber fuel hoses connecting the fuel pipes on the chassis to the fuel pump or carburetor on the engine. Rubber hoses are flexible and can be cut to length as required, but they have a tendency to perish over time and can rub through if not properly secured.
You can find Poulan Pro products both in-store and online at home improvement retailers, hardware stores, and mass merchants all over North America. We are here to help you tackle… ANY YARD.
Over time, the spark arrestor can become clogged with soot. If the spark arrestor is clogged, the chainsaw may run stall or run rough. To unclog the spark arrestor, remove it and clean it with a wire brush. You can also replace the spark arrestor.
If the carburetor is clogged, it may only work with the choke engaged, which is not a good way to be running your engine. Cleaning the carburetor and replacing some of the internal parts with a new carb kit is a great way to get your carburetor running properly again.
Check your air filter. A dirty air filter can affect your gas chainsaw`s ability to cut. Issues like low power, poor performance or if the engine`s stalling during cutting could all be signs you need to clean it. Follow the owner manual guidelines for maintenance.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Is it straight gas or mixed? – Poulan Pro 14" Gas Chainsaw 33CC P3314
ANSWER : It uses a gas/oil mix. 40:1Hope this helps.

Read Full Q/A … : Poulan

How to put gas and oil in it.
ANSWER : It’s one fill of petrol to one cap of two stroke oil.
If you want to put in more, that is no problem, but it will smoke a lot!

Read Full Q/A … : Poulan

I put oil in gas and gas in the oil can it be fixed
ANSWER : YES IT CAN. TAKE OFF BOTH CAPS AND TURN THE SAW OVER AND EMPTY THE TANKS. GO TO AN AUTO PARTS STORE AND BUY A GOOD DEGREASER THAT YOU CAN SPRAY IN THE TANKS AND WASH CLEAN. WAIT TILL DRY AND REFILL HTE RIGFHT WAY.

Read Full Q/A … : Poulan

Can you adjust the oil pump – Poulan Pro 42CC 2 Cycle Chainsaw, 18"
ANSWER : Depends on the saw. If it is adjustable then it will be adjusted from the bottom of the saw. Most have a diagram on the bottom showing which direction to turn the screw

Read Full Q/A … : Poulan

I need the gas mix oil ratio for the Poluan Pro 42…
ANSWER : 40:1 gas to oil ratio.

Read Full Q/A … : Poulan

Pp4218 stopped running abruptly. Can’t budge the starter rope.
ANSWER : Did you respected the GAS/OIL ratio? did it over heated? … from the sound of this, the engin is siesed (lack of lubricating or over heated) sorry i’m not an expert it is just a suggestionGood luck!

Read Full Q/A … : Poulan

I have a Pouan Pro. I can start it but then when I give it gas it seems to have no power. It doesn’t die, just gets no power. Occasionally it revs.
ANSWER : It may well be running too rich because the air filter is blocked, remove the filter and just try the revs again free running, if ok, clean/replace the filter.

Read Full Q/A … : Poulan

What kind of oil do i MIX WITH THE FUEL – Poulan P3416 16Inch 34cc 2Cycle Gas Powered Chain Saw
ANSWER : 2 STROKE OIL.THE ONE 2 STROKE MOTORCYCLE USE.If you need more help post back!
Thumbs and testimonial are welcome!

Read Full Q/A … : Poulan