tch works fine.
Garden

Experienced gardeners share their insights in answering this question :
Sounds like you either have a bad switch, or possibly a wire has came loose on the inside. Any electrician or reasonably handy handyman can fix this.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Perhaps the most common cause for a ceiling fan remotes not working is either a lack of batteries or dead batteries. If your remote control has an indicator light, check to see if it comes on. If it doesn`t, that`s a good sign that it has a battery problem.
Turning the fan on and off at the switch can resolve some wireless issues. Reset the Wi-Fi module by removing the battery door. Press and hold the reset button for 5 seconds. The fan and light LEDs will flash once the module has been reset.
A: To fix it all you have to do is replace the battery. I just had this exact problem happen to me and replacing the battery fixed it.
On the back of the remote control – remove the battery cover; you`ll see a Learn Switch on it; cut the power to the fan from the breaker or wall switch for 1 minute, once you turn it back on you have 60 seconds to program the remote to your fan: PRESS and HOLD the button with the end of a pen or an open paperclip until
First, if your ceiling fan is working but the lights aren`t, I recommend making sure the bulbs are secured in place and not burned out. Tip: you can test them in a lamp to see if they work in a different spot.
Hunter fans that come with pull chains are compatible with either a handheld remote or a wall control that mounts inside the wall switch.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Pull cord is difficult to pull after third pull becomes stuck but will turn if pull hard repeats every three to four pulls.
ANSWER : No response to clarification request.

Read Full Q/A … : Garden

My chainsaw starts when there is no bar and chain on it but when I put the bar chain and side casing back on tighten the chain and pull the starter cord it is hard to pull and then the chain goes loose again
ANSWER : Have you just replaced the chain?If so there is a possibility the chain and drive sprocket don’t match causing the engaging spurs to ride on the sprocket teeth

Read Full Q/A … : Garden

Chain saw won’t start – pull starter pulley hard to pull?
ANSWER : If it worked fine the last time you used it, then pull the spark plug and try pulling the rope. See if it’s easier or if gas shoots out of the plug hole. I’ve seen this happen when the diaphram in the carb goes bad from sitting over winter. It loads up the cylider with fuel and makes it very difficult to pull the rope. If there is no fuel in the cyliner and it’s still hard to pull, make sure there is nothing binding the clutch/sprocket. I’ve had chucks of wook lodged in there that caused it to bind the crank output, which resulted in a hard pull on the rope as well.

Read Full Q/A … : Garden

Our Hunter fan has the 4 tulip lights, and 5 blades, brand new. The light switch worked once and now the pull chain doesn’t. The fan pull switch works fine.
ANSWER : Sounds like you either have a bad switch, or possibly a wire has came loose on the inside. Any electrician or reasonably handy handyman can fix this.

Read Full Q/A … : Garden

I have a 2.5 turbo craftsman chainsaw that I just rebuilt the carb. this chain saw was given to me and was not working when I was given this gift I knew it had worked before knowing the people that gave me the chainsaw. I got the engine running with the rebuil then it would not turn off. I had pull the plug wire. though maybe it was the switch, but the parts store tested and said the switch was fine. I checked to see if it had come undone from the ciol, but it had not. I disconnected the switch and it will still start then while it was running I tried to connectthe two wires going to the switch thinking it would turn off, but it did not. what do you suggest?
ANSWER : Hi, if you short the kill switch terminal on the coil and you still have spark then the earthing circuit inside the coil is fried. If this is the case the only way to fix your problem is replace the coil. Regards Phil.

Read Full Q/A … : Garden

Kill switch will not stop motor – Husqvarna 350 18 Inch Gas Chainsaw 52CC Fully Assembled Brand New 18"
ANSWER : Check and make sure the wires are plugged into switch.If that don,t work it has a bad switch.

Read Full Q/A … : Garden

Chain saw chain stopped moving
ANSWER : Was it running and shut down and was froze or when you went to restart it was frozen? Two things I have seen cause this other than a seized engine. One – chain bound up. Remove side cover and inspect chain mechanism. Two- the pull cord is bound up. Remove the pull cord cover and inspect.

Read Full Q/A … : Garden

How do I tighten the chain on my Remington 14 in. 2 hp electric chain saw? Have used tightening screw, does do anything. Loosened the blade bolts trying to move the blade out slightly. Doesn’t work…
ANSWER : Mitch if you attempted what is in the manual, and it is not working we would have to see and touch the saw to determine what has failed. If you loosened the bar bolts before trying the adjuster and it did not work, I suggest a trip to a local saw shop.

Chain adjustment pages 1, 8 and 9. This is from a Remington OM http://shoppingcart.msservicecompany.com/msservice_net/product_files/107624%2001/107624-01-EL-8-OM.pdf
If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou

Read Full Q/A … : Garden