Stihl
I have checked and cleaned all in and out flow holes for the chain saw oil. It is still not lubricating the chain.
How to Identify and Fix Common Gardening Problems ?
We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :
The Right Amount of Chainsaw Oil
As you apply full throttle, a thin line of oil should appear on the paper. Once you see this thin line of oil, you know your bar and chain assembly is getting the proper amount of oil.
The most common reasons why your automatic oiler isn`t working are: Your chainsaw`s oil tank is empty. The chainsaw oiler is clogged. The oil pump is broken.
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there`s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
STIHL recommends that you do not run your engine at wide open throttle without a load. A blower is under a load at all times, a trimmer is under a load as long as the trimmer head is in place and the line is to the correct length, while a chainsaw is under a load when the bar and chain are in a cut.
One tell-tale sign that a chainsaw has flooded is the smell of fresh petrol near the muffler. To ascertain whether this is indeed the problem, simply disassemble the part, pull the starter cord as if you were switching on the engine, then dry it, reassemble it and try switching it on again.
Unopened container shelf life: 4 years in originally sealed containers. Container already opened shelf life: up to 4 years if stored in a firmly closed container, in a dark and dry location, at cool (up to 25°C/77°F) constant temperatures.
Locate the oil adjuster screw on the bottom of the chainsaw. Turning this screw will adjust the oil feed rate. Turn the screw clockwise to increase the oil feed. Turn the screw counterclockwise to decrease the oil feed.
With a narrow flat-tipped screwdriver, adjust the oil flow. To increase the oil flow, turn the automatic oiler adjustment screw counterclockwise.
Contact With The Ground
With a single contact with the ground while running, a chainsaw can become very dull. This is because the ground contains sand and dust which is abrasive and contains a lot of tiny rocks. To avoid such occurrences, avoid cutting wood placed on the ground.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
What kind of oil in the oil tank and how much for the remington electric pole saw ?
ANSWER : Bar & chain oil is the best. You can use regular or synthetic. Some say you can use atf (auto transmission fluid) or sae30 oil. I use bar & chain oil.
Read Full Q/A … : Stihl
Dont know what type of oil to use – Toro Power Lawn Mower
ANSWER : Put straight 30 weight motor oil in it. Not 10W30 or any multi-viscosity oil. Straight 30 weight motor oil. If you’re doing a complete oil change, then you may want to use Synthetic 30 weight, which will last longer between oil changes and also make your engine last longer (but it costs more too). Best of luck to you.James
Read Full Q/A … : Stihl
I have a husqvarna 137 chainsaw. The problem is with the bar oil. When the saw runs oil is flowing but where the rubber corner piece which allows the oil to flow out of appears to be just dripping the oil straight out. It looks like it should fill a small reservoir behind the metal plate and the oil then moves upwards where the chains drags the oil through the oil hole on the bar which is moving outwards as in the top chain on the bar. However the chain-brake area is just getting messy with oil splattering all over and the bar not actually getting oiled. I have fitted a new metal plate to see if the corner of the original was not sealing properly but that has not helped. The bar holes are clean. Any suggestions as I can’t see what it could be?
ANSWER : It’s the rubbers. I had the same problem with my 137 and 141. The rubbers shrink over time and the oil never makes it up the channel. The replacement part is one piece and less prone to leaking than the original 2 piece design.
Read Full Q/A … : Stihl
My husky 455 rancher is not oiling the chain properly. I have tried to clean all the oil ports on the bar and saw but it still is hardly pumping any oil to the chain. What could be the problem? How does the oiling system work?
ANSWER : The problem is very likely to be a clogged but more likely faulty internal oil pump (especially if your chainsaw is old).Hope it helps.
Read Full Q/A … : Stihl
Ms 170 leaks bar chain oil out bottom, no oil on chain
ANSWER : Your clutch drum bearing has gone bad, letting the clutch drum to move around and cut into the oiler behind it, so now it just pumps the oil out that hole. You have to get that fixed to use the saw, otherwise you’re going to cause catastrophic damage to the saw very soon.
Read Full Q/A … : Stihl
2700 Series Presser Washer, and I need to change the “engine” oil. There on two oil “yellow” fill point, and the manual talks about changing the pump oil. How exactly do I change the engine oil?
ANSWER : Look for a drain plug on the base of the engine.Take the fill cap off also, and it’ll drain easier.
Read Full Q/A … : Stihl
My 290 isn’t oiling chain. I tried adjusting oil flow and still no oil?
ANSWER : You have to remove the bar and clean it out
Read Full Q/A … : Stihl
Where is the oil drain plug – Troy Bilt 5.5hp Self Propelled Mower
ANSWER : You probably dont have one!
The best way to drain is to warm up the engine *(to suspend the dirt and metal and get the oil flowing) Then tip the mower to the side with the oil filler with the dipstick removed. The oil just pours out!
Get a dog dish sized bowl and catch the waste oil for disposal.
Good luck and be careful!
Read Full Q/A … : Stihl
