Cs-310, 12″ Replacement Chainsaw Chain 45dl 3/8″

Experienced gardeners share their insights in answering this question :
Take it back to the dealer.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

If your chainsaw is using too much bar oil, you may need to clean the bar and chain and rid it of built-up dirt and debris. You can do this by spraying a degreaser onto the bar and chain and letting it sit for a few minutes before wiping them clean with a rag.
The fuel and oil mixture should always be 2% (50:1).
If your chainsaw chain is running slowly or your fuel tank runs dry much more quickly than it should, chances are pretty good that you need to add bar and chain oil – and quick. The bar and the chain are in constant contact with one another.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My 290 isn’t oiling chain. I tried adjusting oil flow and still no oil?
ANSWER : You have to remove the bar and clean it out

Oil is not lubing the chain on bar, what would be causing it?

When using the chainsaw, the chainsaw siezes, and makes the engine run sluggish. The bar and chain we not is not getting oil. The oil reservoir is fulled.

Hope this is not one of those ********, pay us first before we help us website situation.

ANSWER : Sounds like the ports on the bar are possibly clogged with debris or the oil lines going down to the bar are clogged. Check both of them to see if that might be the problem.

Dont know what type of oil to use – Toro Power Lawn Mower
ANSWER : Put straight 30 weight motor oil in it. Not 10W30 or any multi-viscosity oil. Straight 30 weight motor oil. If you’re doing a complete oil change, then you may want to use Synthetic 30 weight, which will last longer between oil changes and also make your engine last longer (but it costs more too). Best of luck to you.James

I have only used my saw a handful of times and it has always done this since i bought it new at lowes. It wont lube the chain with oil and gets vry hot at the clutch it will go through a tank of gas to a half of a tank of bar oil. and like i said it has always been this way whats possibly wrong with the saw or did i buy a lemon
ANSWER : I have the exact same saw. I bought it new 6 months ago also from lowes. It has the exact
Same problems you are describing. It does not appear to be oiling the chain enough, the
Chain is visibly dry,very hot , and dulls quickly. It uses a half tank of oil to a tank of gas. I am
Also in search of an answer.

I have a husqvarna 137 chainsaw. The problem is with the bar oil. When the saw runs oil is flowing but where the rubber corner piece which allows the oil to flow out of appears to be just dripping the oil straight out. It looks like it should fill a small reservoir behind the metal plate and the oil then moves upwards where the chains drags the oil through the oil hole on the bar which is moving outwards as in the top chain on the bar. However the chain-brake area is just getting messy with oil splattering all over and the bar not actually getting oiled. I have fitted a new metal plate to see if the corner of the original was not sealing properly but that has not helped. The bar holes are clean. Any suggestions as I can’t see what it could be?
ANSWER : It’s the rubbers. I had the same problem with my 137 and 141. The rubbers shrink over time and the oil never makes it up the channel. The replacement part is one piece and less prone to leaking than the original 2 piece design.

What kind of oil in the oil tank and how much for the remington electric pole saw ?
ANSWER : Bar & chain oil is the best. You can use regular or synthetic. Some say you can use atf (auto transmission fluid) or sae30 oil. I use bar & chain oil.

On a husqavarna 362 xp special 71cc chainsaw very little oil is coming out to the chain i have removed the chain and bar and cleaned and still very little oil is making it to the chain what should i do ??
ANSWER : Check to see if there is an oil-volume adjustment screw located near the lower part of the chain where it goes into the cover, but mounted in the main case. It might be underneath the case in about the same location. Turn it CCW somewhat, if found, and check for oiling by holding the bar tip running at speed near some cardboard. If properly oiled, it will throw off a thin line of oil after several moments. If there is no adjustment, then you will have to investigate the oil pump, lines, and filter/valve in the oil tank. Make sure to clean the small oil passages in the drive end of the bar. Hope this helps!

Husqvarna iz4817 change oil light needs to be reset
ANSWER : The oil change reminder will flash at 49 hrs for 2 hrs then reset itself. It will do this every 50 hrs.