Mi-T-M CM-1250-0MEH NA Chore Master 1250 PSI Chore Master…

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The number one cause of low or no pressure when using a pressure washer is a blocked or worn nozzle. Blocked nozzles will prevent water from escaping, while a worn nozzle will allow too much water to pass through, causing the pressure to drop.
If your pressure washer is refusing to work or even turn on, the culprit could potentially be the power switches. Most pressure washers use two micro switches that disconnect both the live and neutral connections between the supply and the motor. These switches can jam cutting the power out from reaching the motor.
If your pressure washer starts and runs fine, but there`s no pressure or no water coming from the pump, it could be a clogged wand, hose or inlet filter. Fortunately, this is an easy pressure washer problem to repair. Begin isolating the problem by hooking a water hose to the washer`s inlet and turning it on.
If the pump is leaking, the cause may be minor and easy to repair. Check the seals, packings, and O-rings for wear. These can easily be replaced, saving you the cost of a new pump. However, major leaks such as the ones caused by cracked or damaged plungers, can lead to pump failures.
Using an old, worn-out nozzle is a common cause of lost pressure, and also has one of the simplest fixes. All you need to do is replace the nozzle and make sure you`re using the proper size. Don`t go by the color of the nozzle, make sure you check the orifice size.
One of the most common causes of screenwash issues is clogged washer nozzles. This happens when small particles of dust and dirt get in the nozzles attached to the top of the bonnet, preventing the spray from working. Use a safety pin or needle to prod inside the nozzles and clean the blockage.
You may need to rebuild or replace the pump. If the pump is more than a few years old, and you use the pressure washer fairly often, replace the pump. If the pump is relatively new, and you don`t use the pressure washer often, either rebuild the pump or replace the pump seals.
If you`re experiencing low pressure in a specific area, check for clogging or corrosion that could be slowing water flow. Issues with seals and connections can impact the water pressure coming out of the faucet, so it is important to not only inspect the faucet and fixture themselves but the connections as well.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Oil appears to have come out of the oil filler cap. Is this a sign of overfilling the oil, or something else?
ANSWER : Id definitley say its over filled. try checking the dipstick

What oil do i use in the pump? The oil is milky and needs changing.
ANSWER : Well you can use direct recommended from Ace Hardware see link.

http://www.acehardware.com/product/index.jsp?productId=1340266

They recommend 250 hours, but i’d change more often, like you said when it’s milky. If it begins to get water in the oil sooner, that indicates your piston to crankcase seal is beginning to leak.

No pressure Pump reassembly. I purchased a new pump and installed it. Got machine back together and I’m not getting any pressure. What would be the signs if I don’t have the shaft key in properly? Or any other suggestions?
Water comes out of nozzle with pressure for a quick second then no pressure, just water. This is a brand new pump so was curious if I installed it wrong. Wondering before taking it apart again.
ANSWER : No pressure would be a sign that the key was not in properly.

My pressure washer will start for a second and then shuts down. I just bought it from a friend and don,t think the springs to the govner are right but not sure.would like a skicamitc of the engine or manual so i can see if they are right
ANSWER : When you start your engine open wand trigger this will probably allow you to get the engine warmed up and I think it’ll work for you it used to work for us .

Need help in getting Honda engine on NorthStar pressure washer to run.
ANSWER : Could be low water pressure I have found.Also, I purchased a can of “stuff” at Lowes today which allows you to circulate a liquid substance which lubricates the pressure pump….the pump could be frozen up…I have a rotating nozzle which I bought…and it had frozen up…this stuff works

1750 psi Electric Pressure Washer: My pressure washer is losing pressure and is pulsa…
ANSWER : If the pressure washer is pulsating then that is a sign of check valve failure. You may be able to clean of replace the check valves. Replacing the head is the wrong way to go. This is completely unnecessary. If you can tell me the model number of your pressure washer then I can assist you better in pointing you in the right direction.

Has no pressure, builds up when not holding trigger on gun, but when i press trigger shoots of with pressure the nothing just water comes out.

This pressure washer will continue to build pressure when you let off the trigger. I have replaced the hose 3 times because the pump continues to pump until it blows the hose. The pump will not stop pumping!
ANSWER : You have a defective pressure release valve or someone has misadjusted.