17.5 hp 42 in. Deck Lawn Tractor – CA Model

I RANMY 1987 SEARS GARDEN WITH 18HP B&S TWIN CYL WITH HORIZONTAL SHAFT OUT OF OIL I SHUT IT OFF WHEN IT STARTED LOOSING POWER AND PUT OIL IN IT AND SPRAYED PENETRAITING OIL DOWN SPARK PLUG HOLE AND IT STARTED RIGHT UP BUT NOW IT REALLY KNOCKS WHAT DO YOU THINK IT WILL TAKE TO FIX IT MODEL NUMBER OF MOTOR IS422437. TYPE NUMBER1209-01
Experienced gardeners share their insights in answering this question :
If you don’t run it any longer you make be able to replace the connecting rods and clean the aluminum from the rods off crankshaft with a very fine emery cloth. A clyliner hone and a new set of rings would also be needed.providing the cylinders arent scored. A gasket set and parts would probably set you back about 100 to 150.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

This genuine 500cc Briggs & Stratton single cylinder engine offers dependable power for your equipment needs.
Lawn Tractor

Engine size range from 18-25 hp and most come with a single cylinder with step-up models having a V twin. Some fancier models also feature engines with electronic fuel injection.

Rotary walk-behind lawn mowers are generally powered with gasoline and have engines that are two horsepower to seven horsepower. Riding lawn mowers, on the other hand, have 13 horsepower to 30 horsepower engines because they`re so much bigger and heavier.
Vanguard 18 HP Petrol Engine 570cc.
For this example, we will convert HP to CC. The horsepower in the problem is provided as 40 HP. Next, we rearrange the equation to solve for CC. CC = HP*15 = 40*15 = 600 CC.
Make sure you get the right tractor for your lawn size. 1/2 – 1 acre — For a lawn this size, you`ll want a riding lawn mower with a cutting width of up to 42″ and at least a 14 HP engine. 1 – 2 acres — For yards in this size range, a riding lawn mower with a 42″ or 46″ deck and an engine in the 14 – 16 HP is necessary.
Walk-mower engines range from 140-cc to 190-cc. Choose a larger engine for tough cutting conditions, such as tall and wet grass, bagging, leaf mulching, or maintenance mowing in which you`re cutting down weeds.
For lawn mowers with up to a 42-inch cutting deck, look for at least a 14-hp engine to adequately power the deck and the drive wheels. For a 42- to 46-inch cutting deck, a 14- to 16-hp engine will be ideal. Mowers with a 46-inch to 54-inch cutting deck require an 18- to 24-hp engine.
We wouldn`t recommend going below 25 engine hp, but aside from that, you need to assess your land and your needs. If you need to do basic mowing on flat terrain, find a compact tractor with 25 to 30 hp. If you need something more substantial for plowing, invest in the 45 to 85 hp range.
For most small engines 32.5 CC is equal to 1 horsepower. CCs are a unit based on engine volume while horsepower is a measure of the pulling power generated by the engine.
Vanguard 16 HP Petrol Engine 479cc.

Lawn scarifier motor runs slow than starts to smoke
ANSWER : What sort of scarifier is it?

SMOKE AND SPARKS OUT OF ELECTRIC MOTOR ON FLYMO MOWER
ANSWER : No doubt the brushes have decided they need replaced .

The motor got hot & smoked so I assume I need a new motor. To open the case one needs a really long shafted Phillips screwdriver. Any ideas of where to get a motor an the long shafted screwdriver?
I live in Minneapolis.
ANSWER : As for the motor two of the best suppliers that I have found are washer specialties or grainger industrial supply. They both have distributors nationwide so you should have no trouble finding one nearby.The screwdriver you can get at auto zone or napa. Hope this helps you. Thanks. For the motor you will need h.p. rating manufacture name voltage rating and shaft diameter. The model number would be helpful to.

I have a mt2000-h magnum pump, but did not get the controlls with the pump. Im trying to figure out how to get the two speeds out of the motor when i only have one set of motor leads for the 220v hook up. motor data tag says 1750-3425 for motor rpm. how does this motor produce two differant rpm’s without two differant sets of windings?
ANSWER : You have two windings if it is two speed. What you need is a switch
before your wires come into the motor you need to take one of the leads and run it through a high low switch. This will simply take one of your 110v lines and make it go to high and low speed on the motor.
Green will go to ground, one 110v line will go to common and the other goes to the switch. It comes out as two leads. One will hook up to the low speed terminal and the other will hook to the high speed terminal in the back of the motor.

My pole saw has lost power..I look at the motor and it is sparking like mad
ANSWER : Either the brushes are bad, OR worse iis that one of the armature windings has shorted or is open. Brishes are easy fix, shorted armature is more expensive.

Motor turns but shaft does not

Drive shaft not engaging – Ryobi 30 Cubic Centimeter Curved Shaft Gas Trimmer
ANSWER : Hi there Reyles,On this model, if yo rev the engine and the head just sits there, it can be one of two things.

Clutch not engaging (unlikely)
Broken flex shaft (likely)You need to partially disassemble the unit to find out. I believe you will need a T25 or T27 torx head. Remove the screws from the clutch housing that connects the engine to the shaft.Pull it apart. Spin the shaft manually. If nothing its the shaft. Otherwise its the clutch.Best regardsMike

Motorsmoke it get hot and quit working.It is under warrenty I ,need manufacturer phone number.thank’s.
ANSWER : If you are working on a remington chain saw.all i have for you is bad news….remington is no longer in business……..someone did buy them out but no body is telling me who it is or where you can get parts from.sorry to tell you this……hope this helped.let me know…………………