Scotts Company

I have a Scotts Speedy Green EdgeGuard Mini; I need to spread 2.3 lbs per 1,000 square feet; what should be the setting

I am putting down pre-emergent (dimension)

I believe the spreader goes from 1-15

Experienced gardeners share their insights in answering this question :
First, I went to the products website, in this case Lesco and looked up the spreader settings:https://www.johndeerelandscapes.com/home/spreader-settings.aspxThen, I went to Scotts website and looked up spreader settings:http://www.scotts.com/smg/node2/SCOTTSCOM/lawn-care/lookup-spreader-settings/7800015-24900013-sI cross referenced a product on the Scotts website that uses the same settings as one of those listed on the Lesco website and I found my settings that way.In my case I was using Lesco Pre-M 0.86% 0-0-7 and wanted to apply 5.3 lbs/1000ft. My spreader was a Scotts Turf Builder EdgeGuard Mini with settings from 0-15. I found out by cross referencing that the Scotts Speedy Green 1000 and my spreader used the same settings. So I ended up using the recommended setting of 5.5, as listed on the Lesco website for the Scotts Speedy Green 1000, to apply 5.3 lbs/1000ft of pre emergent using my Scotts EdgeGuard Mini. Hope this helps!

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

The label calls for 2 to 3 pounds per 1000 square feet. If your spreader settings go from 1 to 10 (1 letting out the least and 10 letting out the most) you typically want to be around a 2 setting. If your spreader goes from 1 to 20, you should probably be around a 4 setting.
The setting that you will use when applying Bifen Granules with a Scotts Edgeguard DLX is a 2 or a 3 depending on how quickly you walk.
Place your spreader setting on a low setting (usually one-fourth of the spreader setting range or less). Spread the material over a 50 x 20-foot area (1,000 square feet). If there is material left over, increase your setting. If you come up short, decrease your setting.
In general, the smaller you set your spreader setting the smaller the hole and the slower the material releases from the hopper. There are many different brands of spreaders on the market, and, new or old, it is highly recommended to properly calibrate your spreader before the first use in the spring.
ft. or 8 lbs per 1000 sq ft. using a rotary type spreader.
For ScottsĀ® Grass Seed Products:

Spreader settings can be found via the Download Label link under the “Specs & Details” section for that product.

If you want to use a manual process to find out the best estimate for your spreader setting, a good starting point is to consider the following: 1 lb per 1,000 sq ft = 43.6 lbs per acre. 100 lbs per acre = 2.5 lbs per 1,000 square feet.
SPREADER SETTINGS FOR THIS PRODUCT

The suggested settings should provide an application rate of 3.5 pounds per 1,000 square feet or 150 pounds per acre. Application rates will vary dependent upon speed, equipment wear and condition of spreader.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have a speedy green spreader. I would like to know what setting to use for overseeding. The bag of seed does not have any settings on it.
ANSWER : It’s all is dependent on your square footage i can’t believe it’s not on your bag but maybe try Scotts website. or call your local home center.

Read Full Q/A … : Scotts Company

Ineed the setting instructions. What the openning (gap)has to be at and what the number on the setting handle is when you adjust the openning so as to get the proper adjustments. I have a Scotts Speedy Green Spredder
ANSWER : On the back of the feed that you intend to use it is normally printed at what setting it should be You can aslo gauge it for your self be the flow of the granuals a rough guide is 5 or 6

Read Full Q/A … : Scotts Company

This is a Scotts Speedy Green 2000 model. What is the problem when the flat thing below the hopper quits turning to throw the fertilizer out onto the yard?
ANSWER : It’s important to have precisely the right setting. A little wide is better, because the product you’re spreading isn’t always even, but you’ll have to walk faster to ensure you don’t over apply. This is a notorious problem with those plastic spreaders – I’ve used them lots – and I find that if you stop suddenly with fertilizer in the hopper it instantly stops up. Backing up quickly, then jerking it forward seems to help most of the time.

Make sure you close the chute before you stop moving, and be quick with the chute release. Also, don’t fill it too much because when you run into this problem it makes it more difficult to remedy.

Read Full Q/A … : Scotts Company

I have a speedy green 1000 and the drop chute will not close is there a repair kit for this machine?
ANSWER : Phil, Check the attached links,instruction and guides contact Scotts if you have to. Good luck
“I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info.”
Help Center Contact Lawn and Grass Experts Scotts

Scotts Speedygreen 1000 law spreader spring repair

Replacing Rusted Axle on Scotts Speedy Green Spreader

scotts speedy green 1000 parts diagram Google Search

Read Full Q/A … : Scotts Company

Have Scotts Edgeguard DLX. The fertilizer is from Intermountain Farmsers- The option for the Scotts brand is Scotts Speady Green. They give three options the 1000,2000 and 3000. Which option is teh Edgeguard?
ANSWER : I realize this is an older question but in case anyone has a similar question The Scotts Edgeguard DLX equivalent would be the Speedy Green 3000 suggested setting.

Read Full Q/A … : Scotts Company

Cable on edgeguard broken – Scotts Company Scotts Lawns Edgeguard Deluxe Spreader
ANSWER : Www.scotts.com/smg/…/index.jsp?..

Read Full Q/A … : Scotts Company

Speedy Green Parts
ANSWER : Replacement parts for your model can be found at amazon, click here and take a look: Amazon com scotts lawn parts. I hope this was helpful. Cheers

Read Full Q/A … : Scotts Company

Trying to figure out the spreader setting for some bug killer for my lawn. I have a Scott’s Basic Spreader. The instructions on the bag include Scott’s Speedy Green Spreader setting at 2 1/2 for 2lbs per 1000 sq. ft. What would that translate to for my basic spreader?
ANSWER : You can safely use the recommened settings for the SpeedyGreen in your Scotts Basic Spreader. Hilary @Scotts

Read Full Q/A … : Scotts Company