John Deere

Experienced gardeners share their insights in answering this question :
Repair your vehicle right away. Just click on the link I attach.
John Deere 4100 Workshop Service Repair Manual

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

John Deere PTO switches are designed to provide reliable performance for everyday use for your toughest task. John Deere PTO switches are designed to exact specifications for a firm engage or disengage. John Deere PTO switches are the replacement choice for you. AM147972 replaces GY22356.
If you`re using a multimeter, set the instrument`s dial to the “continuity or resistance/ohms” setting. Touch each tester probe to one of the screw terminals, then turn the switch lever on and off.
Turn on your multimeter and switch the dial to the DC voltage position. This is marked with a V next to a solid line with a dotted line underneath. Connect the black test lead to a COM pin on your PSU`s connector. Connect the red test lead to the PSU pin you want to test.
For power shift operation, when a power shift PTO is engaged, a solenoid is energized. Air or hydraulic fluid then compresses a clutch pack in the PTO. This locks the PTO output gear to the output shaft and allows work to be done. When the power shift PTO is disengaged, the solenoid de-energizes.
Powershift PTO engagement problems could be from blocked hoses or fittings, bad connections or ground or the solenoid. Mechanical PTO engagement problems could originate from low air pressure, improper cable installation or back lash too tight.
When the Power Take Off (PTO) switch is turned ON, 12 volts is sent to the PTO solenoid to engage the PTO. This sends transmission pressure to the PTO to engage. When pressure is sensed, the PTO pressure switch sends a signal (usually ground signal), to the chassis controller indicating that the PTO is engaged.
A low charge may not provide enough juice to engage the PTO. If you do hear the click, there is power going to it. There could be a problem with safety switches. On most newer model lawn mowers, the brake has to be disengaged or off for the blades to operate.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Need the pto to work on a 6300 john deere tractor we have changed the fuses and changed the sencer on the back can you help
ANSWER : If you have tried a new sensor and a new switch the the next step is to replace the pto solenoid valve.If that proves fruitless then the b.c.u.needs to be replaced or bypassed.The solenoid valve will cure your problem 90% of the time.If that does not work,let me know,i can tell you how to by-pass the b.c.u..

Read Full Q/A … : John Deere

Replace the PTO switch on a John Deere 455
ANSWER : Yes to get the out, just reach underneath the dash up to the switch and as as close as you can to the bottom of the dash squeeze together while puuling up. it come out though the top and disconnect the pig tail there

Read Full Q/A … : John Deere

John deere stx 30 pto wont engage
ANSWER : Check your fuse or for a broken wire( or shorted)

Read Full Q/A … : John Deere

The mower blades on my John Deere stx 38 lawn tractor will not engage. I just installed a new pto switch and when engaged the engine stops.
ANSWER : It sounds like the safety switch under seat is bad

Read Full Q/A … : John Deere

Weak fire out of coil wire – John Deere Pto Clutch For Stx38 And Stx46 Lawn Mowers
ANSWER : This can be due to a dirty flywheel, an improper gap between the flywheel and coil, or a coil that is failing, first check for rust or dirty build up on the flywheel, then check for proper gap, and if neither of those are the issue, replace the coil

Read Full Q/A … : John Deere

I am trying to find a new or second-hand bonnet for my john deer stx38. i live in the gippsland area. any suggestions?
ANSWER : I use www.greenpartstore.com

Read Full Q/A … : John Deere

Looking for information on a John Deere tractor S/N CH0850S017329 and the current estimated value of this tractor with approximately 2,700 hours on it.
ANSWER : Can you please post the model number of the tractor? Thanks

Read Full Q/A … : John Deere

How do i replace a clutch on a JD 3020 tractor
ANSWER : Break it in half, then get with it.

Read Full Q/A … : John Deere

My name is June Strandberg, and I am a florist and gardener in San Francisco. I have been working in the industry for five years, and I love helping people find the perfect floral arrangement for their special occasions. I am also skilled in troubleshooting and fixing gardening tools, so if you are ever having trouble with your tools, please don't hesitate to reach out to me.