18″ Chain Saw Bar 3005 008 4717

Experienced gardeners share their insights in answering this question :
The choke is operated by the fingers on the handle grip…the lever is stop…on…choke…when motor running just flick back up to run mode…the choke butterfly is just a open or closed position in the carb y.

How to Identify and Fix Common Gardening Problems ?

We provide a variety of viewpoints on how to identify and fix common gardening problems. Our sources include academic articles, blog posts, and personal essays from experienced gardeners :

Put your left hand on the front handle and your right foot in the rear handle to secure the chainsaw. Pull the starter rope quickly and smoothly until you hear the engine fire. Disengage the choke (if engaged) and pull the starter rope again to start the engine.
Pulling the choke lever provides proper fuel-starting mixture when the engine is cold. When attempting to start a cold engine, pull the choke lever outward to close. Slowly return the choke to the open position as the engine warms. Leave the choke in the OFF/OPEN position when starting or restarting a warm engine.
If the carburetor is clogged, it may only work with the choke engaged, which is not a good way to be running your engine. Cleaning the carburetor and replacing some of the internal parts with a new carb kit is a great way to get your carburetor running properly again.
The even pull on the starter rope overcomes the engine`s compression to minimize the strength and effort required to start. Stresses caused by quick, uneven movements are avoided. The spring automatically releases the stored energy to the crankshaft, starts it moving and ensures that the engine will start reliably.
Choking happens when an object lodges in the throat or windpipe blocking the flow of air. In adults, a piece of food is usually to blame. Young children often choke on small objects. Choking is life-threatening.
Some chainsaw models use a horizontal squiggle between two clear vertical lines to denote the choke position. Here`s how this process works: Turn the on/off switch to the “on” position and open the choke. This regulates the air-fuel mix to the engine.
A choke valve/cable is designed to restrict the flow of air in the carburettor of an engine. This helps enrich the fuel-air mixture, improving the ability to start an engine in low temperature conditions.
A rough guide is to use Skeet chokes for a target that is less than 25 yards away, ¼ choke for 25-yard targets, ½ choke at 30 yards, ¾ choke at up to 35 yards and Full for anything at 40 yards or more.
A choke valve/cable is designed to restrict the flow of air in the carburettor of an engine. This helps enrich the fuel-air mixture, improving the ability to start an engine in low temperature conditions.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Need a diogram of how the choke on a 026 stihl chainsaw in setup.
ANSWER : The choke is operated by the fingers on the handle grip…the lever is stop…on…choke…when motor running just flick back up to run mode…the choke butterfly is just a open or closed position in the carb y.

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

How to replace a oiler on a stihl chainsaw ? – Stihl Service Manual for 031AV Chainsaw with Parts List
ANSWER : Remove the worm, sealing ring and washer, loosen the pan head screws on the oil pump and replace. Check if the gasket is re-usable.

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

How do I reconnect ,my throttle trigger for ms 260
ANSWER : Remove the top cover on the handle, there is a screw in the bottom of the handle end. put the on off switch in the choke position all the way down, connect rod to throttle on carburetor then slip it into the hole in the trigger. replace operator presence lever making sure the spring is in the notch on the side of it, while holding it in place reinstall the top cover.

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

How to remove stihl 023 handle bar?
ANSWER : There are three mounting points. You need to remove the screws behind the plug caps with a T27 bit. Then, the tank should separate from the crankcase and you can pop the AV mount from the crankcase to replace it.

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

Is there supposed to be a cyntrifical clutch on a stihl 028 av super electronic quickstop?
ANSWER : Yes; see page 37 in your OM. You read it before using your saw right?
http://www.stihlusa.com/stihl_ownersmanuals/STIHL028_with_safety_manual.pdf

If you have more questions or need additional help please reply below and I will get back to you. Thank you for using FixYa and Good Luck. HTH
Lou

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

I HAVE AN O17 STIHL CHAIN SAW AND IT LEAKS CHAIN OIL
EVEN WHEN IT IS NOT BEING USED
ANSWER : That can happen. When you go to store it, open the oil cap and then close it to lose the pressure the pump builds up inside.

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

Starter coil on stihl 017 – Stihl 017 018 Ms170 Ms180 Chainsaw Starter Stbx759
ANSWER : If you are asking for the part number, it is 1130 400 1302 if you have two ground wires and one lead wire. If you only have one ground wire and one lead wire, the part number is 1130 400 1300.

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

How to adjust chainsaw oiler on stihl MS230
ANSWER : You cant. the oiler on an Ms230 is preset and non adjustable. Make sure the oil worm gear isnt damaged

Read Full Q/A … : 18″ Chain Saw Bar 3005 008 4717

My name is June Strandberg, and I am a florist and gardener in San Francisco. I have been working in the industry for five years, and I love helping people find the perfect floral arrangement for their special occasions. I am also skilled in troubleshooting and fixing gardening tools, so if you are ever having trouble with your tools, please don't hesitate to reach out to me.